Cadillac Escalade 2020 Owner'S Manual Download Page 116 | Manualshive

Page: 116 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

116

INSTRUMENTS AND CONTROLS

Phone

While the Phone application page is
displayed, press SEL to enter the
Phone menu. In the Phone menu,
if there is no active phone call, view
recent calls, select from favorites,
or scroll through contacts. If there is
an active call, mute the phone or
switch to handset operation.

Cluster Options Menu

To enter the cluster Options menu:

1. Use the five-way control on the

right side of the steering wheel
to find the Options page in one
of the interactive display zones
on the cluster.

2. Press SEL on the center of the

five-way control to enter the
Options menu.

Units :

Press SEL while Units is

highlighted to enter the Unit menu.
Choose US or metric units by pressing
SEL while the desired item is
highlighted. A checkmark will be
displayed next to the selected item.

Info Pages :

Press SEL while Info

Pages is highlighted to select the
items to be displayed in the DIC info
displays. See

Driver Information Center

.

Head-up Display (HUD) Rotation :

This feature allows for adjusting the
angle of the HUD image. The vehicle
must be in P (Park). Press SEL on the
steering wheel controls while Head-up
Display Rotation is highlighted to
enter Adjust Mode. Press

y

or

z

to

adjust the angle of the HUD display.

Press

S

or

T

to highlight OK, then

press SEL to save the setting. Cancel
can also be selected to cancel the
setting.

Fav Button Options :

Press SEL while

Fav Button Options is highlighted to
select between FAV Primary and SEEK
Primary. This selection allows for
configuration of the

C

and

B

steering wheel controls. When FAV

Primary is selected, pressing

C

and

B

will go to the next or previous

favorite and pressing and holding

C

and

B

will seek. When SEEK Primary

is selected, pressing

C

and

B

will

seek and pressing and holding

C

and

B

will go to the next or previous

favorite.

Display Layout :

Press SEL while

Display Layout is highlighted to
change the configuration of the
cluster. See

“

Reconfigurable

Instrument Cluster

”

earlier in this

section.

Open Source Software :

Press SEL

while Open Source Software is
highlighted to display open source
software information.

Speedometer

The speedometer shows the vehicle's
speed in kilometers per hour (km/h)
or miles per hour (mph).

This vehicle is equipped with an
overspeed warning device. When the
vehicle's speed reaches 120 km/h
(75 mph), a chime will sound.

«
...
114
115
116
117
118
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: JANE Pages: 6

Brand: HALE Pages: 44

Brand: LAMBORGHINI Pages: 48

Brand: Vaisala Pages: 24

QuadraTop Adventure Top S

Brand: Quadratec Pages: 20

Brand: Porsche Pages: 195

Brand: Brodit Pages: 2

Brand: Cadillac Pages: 34

Brand: Jaeger Pages: 17

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: Hella Pages: 21

Brand: POOL-LINE Pages: 2

Brand: Rugged Ridge Pages: 2

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Kia Pages: 233

Brand: Mercedes-Benz Pages: 585

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands