Cadillac Escalade 2020 Owner'S Manual Download Page 303

Page: 303 / 355

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

303

1. Pull to open the trim panel door.

The third row driver side seat
may need to be folded to access
the trim panel door.

2. Lift the acoustic pad to access

the jack and tools.

3. Turn the wing nut retaining the

tool bag (3) counterclockwise to
remove it.

Pull the tool bag toward the front
of the vehicle and lift the rear
portion of the bag upward to
remove it.

4. Turn the jack knob (1)

counterclockwise to release the
jack and wheel blocks from the
bracket.

5. Turn the wing nut retaining the

wheel blocks (2)
counterclockwise to remove the
wheel blocks and the wheel block
retainer.

Use the following tools:

1. Jack
2. Wheel Blocks
3. Jack Handle
4. Jack Handle Extensions
5. Wheel Wrench

To access the spare tire, refer to the
following graphics and instructions:

1. Hoist Assembly
2. Hoist Shaft
3. Hoist Shaft Access

Cover/Hole

4. Jack Handle Extensions
5. Wheel Wrench
6. Spare Tire Lock
7. Hoist End of Extension Tool
8. Hoist Shaft Access Hole
9. Spare Tire (Valve Stem

Pointed Down)

10. Tire/Wheel Retainer
11. Hoist Cable

Summary of Contents for Escalade 2020




































































































































































































































































































































































Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands

Cadillac Escalade 2020, Owner'S Manual

Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands