Cadillac Escalade 2020 Owner'S Manual Download Page 158 | Manualshive

Page: 158 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

158

CLIMATE CONTROLS

OFF :

Press OFF to turn the fan on or

off. When off is selected, the system
will stop air from flowing into the
cabin. If on is selected, any other
buttons are pressed, or any knobs are
turned, the climate control system will
turn on and operate at the current
setting.

w

/

x

:

The temperature can be

adjusted separately for the driver and
the passenger. Press to increase or
decrease the temperature. Press and
hold to rapidly increase or decrease
the temperature.

The driver and passenger
temperatures can also be adjusted by
pressing the controls on the touch
screen.

SYNC :

Touch SYNC on the climate

control display to link all climate zone
settings to the driver settings. Adjust
the driver side temperature control to
change the linked temperature. When
the passenger settings are adjusted,
the SYNC button is displayed when
the temperatures are unlinked.

Rear :

If equipped, touch Rear on the

front climate control display to open
the rear climate control screen. The
rear climate control settings can now
be adjusted from the front
passenger area.

Manual Operation

z 9 y

:

Touch the fan controls on

the climate control display or press
the fan control buttons, to increase or
decrease the fan speed. Touch or press
and hold the fan controls to adjust
speed more quickly. The fan speed
setting displays. Any adjustment of
the fan speed cancels automatic fan
control and the fan can be controlled
manually. Press AUTO to return to
automatic operation.

To turn off the fan and climate
control system, press OFF on the
center stack climate controls. The
airflow will be blocked from entering
in all air delivery modes, except
defrost.

The maximum automatic fan speed
can be set to low, medium, or high. To
adjust Auto Fan Speed, see

“

Climate

and Air Quality

”

under

Personalization

.

Air Delivery Mode Control :

When

the climate information is displayed,
press the desired air delivery mode on
the climate control display to change
the direction of the airflow. The
selected air delivery mode button is
lit. Pressing any of the air delivery
buttons cancels automatic air delivery
control and the direction of the
airflow can be controlled manually.
Press AUTO to return to automatic
operation.

To change the current mode, select
one of the following:

Y

:

Air is directed to the instrument

panel outlets.

\

:

Air is divided between the

instrument panel outlets and the floor
outlets.

[

:

Air is directed to the floor

outlets.

«
...
156
157
158
159
160
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: PAC Pages: 15

Brand: LAMBORGHINI Pages: 48

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Brand: TATA Motors Pages: 156

Brand: TBC Pages: 12

Brand: FAAFTECH Pages: 8

Brand: AutoMaxi Pages: 2

Brand: TEINHOF Pages: 2

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Brand: NavInc Pages: 6

Denali 1094-0185-15

Brand: E&G Classics Pages: 3

Brand: Metra Electronics Pages: 2

Brand: WABCO Pages: 34

FXX ATM Emulator

Brand: BMW Pages: 5

Brand: BMW Pages: 392

Brand: Curt Manufacturing Pages: 4

Brand: ECS Electronics Pages: 42

Brand: PEUGEOT Pages: 404

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands