Cadillac Escalade 2020 Owner'S Manual Download Page 109 | Manualshive

Page: 109 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

109

.

One on the rear of the center
console

.

One in the third row seat on the
driver side

.

One in the rear cargo area on the
passenger side

Lift the cover to access and replace
when not in use.

The accessory power outlets are
powered as follows:

.

The power outlet near the
cupholders on the center console
is powered in Retained Accessory
Power (RAP) mode. This outlet can
be configured to operate using
RAP or battery power. If the power
outlet is used while in the battery
power mode, this could cause
interference between the RKE
transmitter and the vehicle, and
the vehicle may not start. See

Ignition Positions

.

The power outlets inside the
center console and on the rear of
the center console are powered
when the vehicle is started or the
ignition is in ACC/ACCESSORY,

or until the driver door is opened
within 10 minutes of turning off
the vehicle. See

Retained Accessory

.

The power outlets in the third row
seat and in the rear cargo area are
powered at all times.

{

Warning

Power is always supplied to the
outlets. Do not leave electrical
equipment plugged in when the
vehicle is not in use because the
vehicle could catch fire and cause
injury or death.

Caution

Leaving electrical equipment
plugged in for an extended period
of time while the vehicle is off will
drain the battery. Always unplug
electrical equipment when not in
use and do not plug in equipment
that exceeds the maximum 15 amp
rating.

Certain power accessory plugs may
not be compatible with the accessory
power outlet and could overload
vehicle or adapter fuses. If a problem
is experienced, see your dealer.

When adding electrical equipment, be
sure to follow the proper installation
instructions included with the
equipment. See

Add-On Electrical

.

Caution

Hanging heavy equipment from the
power outlet can cause damage not
covered by the vehicle warranty.
The power outlets are designed for
accessory power plugs only, such as
cell phone charge cords.

Power Outlet 220V/230V Volt
Alternating Current

For vehicles with 220V/230V outlet,
use only accessories rated for
220V/230V.

This power outlet can be used to plug
in electrical equipment that uses a
maximum limit of 150 watts.

«
...
107
108
109
110
111
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Suzuki Pages: 16

Brand: Saab Pages: 75

Brand: Valeo Pages: 17

Brand: DANA Pages: 42

Brand: dallara Pages: 37

Brand: Yakima Pages: 8

Brand: cam Pages: 28

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

Brand: Chevrolet Pages: 356

Brand: Ford Pages: 272

Brand: Pontiac Pages: 376

Brand: Jeep Pages: 712

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: AddSecure Pages: 14

Dodge Challenger SRT8®Challenger SRT8 392 2012

Brand: Dodge Pages: 5

Brand: Edelbrock Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands