Cadillac Escalade 2020 Owner'S Manual Download Page 185 | Manualshive

Page: 185 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

185

Caution (Continued)

and drain the battery. Wait at least
15 seconds between each try, to let
the cranking motor cool down.

2. If the engine does not start after

five to 10 seconds, especially in
very cold weather (below

−

18 °C

or 0 °F), it could be flooded with
too much gasoline. Try pushing
the accelerator pedal all the way
to the floor and holding it there
as you press ENGINE START/
STOP, for up to a maximum of
15 seconds. Wait at least
15 seconds between each try, to
allow the cranking motor to cool
down. When the engine starts,
let go of the button, and the
accelerator. If the vehicle starts
briefly but then stops again, do
the same thing. This clears the
extra gasoline from the engine.
Do not race the engine
immediately after starting it.
Operate the engine and

transmission gently until the oil
warms up and lubricates all
moving parts.

Retained Accessory
Power (RAP)

When the ignition is turned from on
to off, the following features (if
equipped) will continue to function
for up to 10 minutes, or until the
driver door is opened. These features
will also work when the ignition is in
RUN or ACC/ACCESSORY:

.

Infotainment System

.

Power Windows (during RAP this
functionality will be lost when any
door is opened)

.

Sunroof (during RAP this
functionality will be lost when any
door is opened)

.

Auxiliary Power Outlet

.

Audio System

.

OnStar System

Shifting Into Park

{

Warning

It can be dangerous to get out of
the vehicle if the shift lever is not
fully in P (Park) with the parking
brake firmly set. The vehicle can
roll. If you have left the engine
running, the vehicle can move
suddenly. You or others could be
injured. To be sure the vehicle will
not move, even when you are on
fairly level ground, use the steps
that follow. If the vehicle has a
four-wheel-drive transfer case with
an N (Neutral) position, and the
transfer case is in N (Neutral), the
vehicle will be free to roll, even if
the shift lever is in P (Park). Be sure
the transfer case is in a drive gear.
If towing a trailer, see

Characteristics and Towing Tips

1. Hold the brake pedal down, then

set the parking brake. See

Parking Brake

.

«
...
183
184
185
186
187
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Green Motion Building

Brand: Eaton Pages: 12

Brand: kaarta Pages: 29

Brand: Sirius Satellite Radio Pages: 8

Brand: Whispbar Pages: 14

Brand: Buick Pages: 20

Brand: Camecho Pages: 2

E60-82-007-02-10

Brand: Eibach Pages: 3

RVS systems RVS-M641

Brand: Safe Fleet Pages: 24

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: TATA Motors Pages: 146

Brand: Cadillac Pages: 538

Brand: XTC Pages: 2

Brand: TigerTough Pages: 7

Dual Clamp Spare Tire Mount

Brand: FACTORY UTV Pages: 2

Brand: Kuda-Phonebase Pages: 3

MagicComfort MSH50

Brand: Waeco Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands