Cadillac Escalade 2020 Owner'S Manual Download Page 131 | Manualshive

Page: 131 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

131

value. This feature can be turned off
by pressing and holding SEL while
viewing this page. If the selected
speed limit is exceeded, a pop-up
warning is displayed and a chime may
sound.

Cruise Set Speed :

Shows the speed

the cruise control or Adaptive Cruise
Control is set to.

Follow Distance Indicator :

When

Adaptive Cruise Control (ACC) is not
engaged, the current follow time to
the vehicle ahead is displayed as a
time value on this page. When ACC
has been engaged, the display
switches to the gap setting page. This
page shows the current gap setting
along with the vehicle ahead indicator.

Battery Voltage :

Shows the current

battery voltage.

Oil Life :

Shows an estimate of the

oil's remaining useful life.
If REMAINING OIL LIFE 99% is
displayed, that means 99% of the
current oil life remains.

When the remaining oil life is low, the
CHANGE ENGINE OIL SOON message
will appear on the display. The oil
should be changed as soon as
possible. See

. In

addition to the engine oil life system
monitoring the oil life, additional
maintenance is recommended. See

Maintenance Schedule

The Oil Life display must be reset
after each oil change. It will not reset
itself. Do not reset the Oil Life display
accidentally at any time other than
when the oil has just been changed.
It cannot be reset accurately until the
next oil change. To reset the engine
oil life system, press and hold SEL for
several seconds while the Oil Life
display is active. See

Engine Oil Life

.

Oil Pressure :

Shows the engine oil

pressure in kPa (kilopascals)
or psi (pounds per square inch).

Engine Hours :

Shows the total

number of hours the engine has run.

Transmission Fluid Temperature :

Shows the temperature of the
automatic transmission fluid in either
degrees Celsius (°C) or degrees
Fahrenheit (°F).

Tire Pressure :

Shows the

approximate pressures of all four tires.
Tire pressure is displayed in either
kilopascal (kPa) or in pounds per
square inch (psi). If the pressure is
low, the value for that tire is shown in
amber. See

Tire Pressure Monitor

and

Tire Pressure Monitor Operation

.

Blank Page :

Allows for no

information to be displayed in the
cluster info display areas.

Head-Up Display (HUD)

{

Warning

If the HUD image is too bright or
too high in your field of view, it
may take you more time to see
things you need to see when it is

(Continued)

«
...
129
130
131
132
133
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: M7 SPEED Pages: 11

Brand: Porsche Pages: 195

Brand: Caltrend Pages: 2

Brand: Audiovox Pages: 1

EGR-3PVE-COLOUR

Brand: EGR Pages: 28

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: Parkeon Pages: 43

Brand: Mobility Networks Pages: 52

Speed & Route Profiler

Brand: Racelogic Pages: 24

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Brand: Mercedes-Benz Pages: 296

Brand: Horn Tools Pages: 12

Brand: Volvo Pages: 18

Brand: Jaeger Pages: 11

Brand: ATS Pages: 12

Brand: Subaru Pages: 2

Brand: Honda Pages: 330

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands