Cadillac Escalade 2020 Owner'S Manual Download Page 213 | Manualshive

Page: 213 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

213

feel or sound different than if the
brakes were applied manually. This is
normal.

Stationary or Very Slow-Moving
Objects

{

Warning

ACC may not detect and react to
stopped or slow-moving vehicles
ahead of you. For example, the
system may not brake for a vehicle
it has never detected moving. This
can occur in stop-and-go traffic or
when a vehicle suddenly appears
due to a vehicle ahead changing
lanes. Your vehicle may not stop
and could cause a crash. Use
caution when using ACC. Your
complete attention is always
required while driving and you
should be ready to take action and
apply the brakes.

ACC Automatically Disengages

ACC may automatically disengage and
the driver will need to manually apply
the brakes to slow the vehicle if:

.

The sensors are blocked.

.

The Traction Control System (TCS)
or electronic stability control
system has activated or been
disabled.

.

There is a fault in the system.

.

The radar falsely reports blockage
when driving in a desert or remote
area with no other vehicles or
roadside objects. A DIC message
may display to indicate that ACC
is temporarily unavailable.

The ACC active indicator will turn
white when ACC is no longer active.

In some cases, when ACC will not
activate, regular Cruise Control may
be used. See

“

Switching Between ACC

and Regular Cruise Control

”

previously

in this section. Always consider
driving conditions before using either
cruise control system.

Notification to Resume ACC

ACC will maintain a following gap
behind a detected vehicle and slow
your vehicle to a stop behind the
detected vehicle.

If the stopped vehicle ahead has
driven away and ACC has not
resumed, the vehicle ahead indicator
will flash as a reminder to check
traffic ahead before proceeding. In
addition, the left and right sides of the
Safety Alert Seat will pulse three
times, or three beeps will sound. See

”

Alert Type

”

and

“

Adaptive Cruise Go

Notifier

”

in

“

Collision/Detection

Systems

”

under

Vehicle Personalization

When the vehicle ahead drives away,
press +RES or the accelerator pedal to
resume cruise control. If stopped for
more than two minutes or if the driver
door is opened and the driver seat belt
is unbuckled, the ACC automatically
applies the Electric Parking Brake
(EPB) to hold the vehicle. The EPB
status light will turn on. See

Parking Brake

. To resume ACC

and release the EPB, press the
accelerator pedal.

A DIC warning message may display
indicating to shift to P (Park) before
exiting the vehicle. See

.

«
...
211
212
213
214
215
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: DAVIS Pages: 32

Brand: Cequent Pages: 9

Gold Cruuse Cruisecontrol GC90

Brand: John Gold Pages: 24

Brand: Whispbar Pages: 14

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: Mercedes-Benz Pages: 54

Ferrari 360 Map Carbon Light

Brand: MAcarbon Pages: 4

Tata Indigo Diesel

Brand: TATA Motors Pages: 190

Prime Design HBR-E-FT33B

Brand: Safe Fleet Pages: 12

Brand: Ecco Pages: 12

Brand: Voxoa Pages: 48

Brand: SNIPER Pages: 2

CARWATT CV12-220C150

Brand: WATT Pages: 26

Brand: BMW Pages: 392

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands