manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

117

A message also displays in the Driver
Information Center (DIC). See

Vehicle

Speed Messages

0

135

.

Odometer

The odometer shows how far the
vehicle has been driven, in either
kilometers or miles.

Trip Odometer

The trip odometer shows how far the
vehicle has been driven since the trip
odometer was last reset.

The trip odometer is accessed and
reset through the Driver Information
Center (DIC). See

Driver Information

Center (DIC)

0

129

.

Tachometer

The tachometer displays the engine
speed in revolutions per minute (rpm).

Fuel Gauge

Balanced Configuration

When the ignition is on, the fuel
gauge indicates about how much fuel
is left in the tank.

There is an arrow near the fuel gauge
pointing to the side of the vehicle the
fuel door is on.

When the indicator nears empty, the
low fuel light comes on. There still is
a little fuel left, but the vehicle should
be refueled soon.

Here are four things that some owners
ask about. None of these show a
problem with the fuel gauge:

.

At the service station, the fuel
pump shuts off before the gauge
reads full.

.

It takes a little more or less fuel to
fill up than the gauge indicated.
For example, the gauge may have
indicated the tank was half full,
but it actually took a little more or
less than half the tank's capacity
to fill the tank.

.

The gauge moves a little while
turning a corner or speeding up.

.

The gauge takes a few seconds to
stabilize after the ignition is
turned on, and goes back to empty
when the ignition is turned off.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

iDataLink maestro Pr 2 Install Manual preview
maestro Pr 2
Brand: iDataLink Pages: 99
Suzuki Movano Owner'S Manual preview
Movano
Brand: Suzuki Pages: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Brand: Torklift Pages: 16
SuperATV AAB-P-RZR900-K2-001 Installation Instructions preview
AAB-P-RZR900-K2-001
Brand: SuperATV Pages: 3
Yescom YES5062 User Manual preview
YES5062
Brand: Yescom Pages: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Brand: Z Automotive Pages: 16
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Brand: Wagan Pages: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Brand: Chevrolet Pages: 50
Connects2 adaptiv mini ADVM-BM1 Fitting & User Manual preview
adaptiv mini ADVM-BM1
Brand: Connects2 Pages: 4
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Brand: STO N SHO Pages: 7
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Brand: Acura Pages: 6
Webasto Telestart T70 Installation Instructions Manual preview
Telestart T70
Brand: Webasto Pages: 23
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
Skoda FABIA II TMB PS 035 Mounting And User Instructions preview
FABIA II TMB PS 035
Brand: Skoda Pages: 16
Rugged Ridge 13551.33 Manual preview
13551.33
Brand: Rugged Ridge Pages: 3
Wallbox PLP1 Installation Manual preview
PLP1
Brand: Wallbox Pages: 21
Mercedes-Benz GLC 2020 Operator'S Manual preview
GLC 2020
Brand: Mercedes-Benz Pages: 66
Jacob Jensen Electronic Parking Disc 3 User Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 17

Brands by name

Popular brands

Load more brands