manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

322

VEHICLE CARE

Tires

Use a stiff brush with tire cleaner to
clean the tires.

Caution

Using petroleum-based tire dressing
products on the vehicle may
damage the paint finish and/or
tires. When applying a tire dressing,
always wipe off any overspray from
all painted surfaces on the vehicle.

Wheels and Wheel Trim

Use a soft, clean cloth with mild soap
and water to clean the wheels. After
rinsing thoroughly with clean water,
dry with a soft, clean towel. A wax
may then be applied.

Caution

Chrome wheels and chrome wheel
trim may be damaged if the vehicle
is not washed after driving on roads
that have been sprayed with

(Continued)

Caution (Continued)

magnesium chloride or calcium
chloride. These are used on roads
for conditions such as dust and ice.
Always wash the chrome with soap
and water after exposure.

Caution

To avoid surface damage on wheels
and wheel trim, do not use strong
soaps, chemicals, abrasive polishes,
cleaners, or brushes. Use only GM
approved cleaners. Do not drive the
vehicle through an automatic car
wash that uses silicon carbide tire/
wheel cleaning brushes. Damage
could occur and the repairs would
not be covered by the vehicle
warranty.

Brake System

Visually inspect brake lines and hoses
for proper hook-up, binding, leaks,
cracks, chafing, etc. Inspect disc brake

pads for wear and rotors for surface
condition. Inspect drum brake linings/
shoes for wear or cracks. Inspect all
other brake parts.

Steering, Suspension, and
Chassis Components

Visually inspect steering, suspension,
and chassis components for damaged,
loose, or missing parts or signs of
wear at least once a year.

Inspect power steering for proper
attachment, connections, binding,
leaks, cracks, chafing, etc.

Visually check constant velocity joint
boots and axle seals for leaks.

At least every other oil change
lubricate the outer tie rod ends .

Control arm ball joints are
maintenance-free.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Mazda 2011 Tribute Brochure & Specs preview
2011 Tribute
Brand: Mazda Pages: 4
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Ecco EW4010 Installation And Operation Instructions Manual preview
EW4010
Brand: Ecco Pages: 9
Ecco EW4009 Installation And Operation Instructions Manual preview
EW4009
Brand: Ecco Pages: 9
TATA Motors Indigo Owner'S Manual & Service Book preview
Indigo
Brand: TATA Motors Pages: 164
RaceChip XLR User Manual preview
XLR
Brand: RaceChip Pages: 20
REVCAMUK MON16AHD Instructions preview
MON16AHD
Brand: REVCAMUK Pages: 4
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Brand: BendPak Pages: 104
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Brand: Pet Gear Pages: 4
Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual preview
PRIME DESIGN HXR-269-E-UM3-80
Brand: Safe Fleet Pages: 12
Volvo 1989 780 Owner'S Manual preview
1989 780
Brand: Volvo Pages: 123
Prorack K623 Fitting Instructions Manual preview
K623
Brand: Prorack Pages: 15
ADS FlashLogic FLC-FORS-FO1B-FLRSFO1-EN Install Manual preview
FlashLogic FLC-FORS-FO1B-FLRSFO1-EN
Brand: ADS Pages: 25
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Brand: Roadmaster Pages: 4
Mopar 82214480 Manual preview
82214480
Brand: Mopar Pages: 17
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Brand: FALCON RIDGE Pages: 6

Brands by name

Popular brands

Load more brands