Cadillac Escalade 2020 Owner'S Manual Download Page 194 | Manualshive

Page: 194 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

194

DRIVING AND OPERATING

Tow/Haul Mode

The Tow/Haul Mode adjusts the
transmission shift pattern to reduce
shift cycling. This provides increased
performance, vehicle control, and
enhanced transmission and engine
cooling when driving down steep hills
or mountain grades, towing,
or hauling heavy loads.

The selector button is on the end of
the shift lever. Turn the Tow/Haul
Mode on and off by pressing the
button. When the Tow/Haul Mode is
enabled, a light on the instrument
cluster will come on.

See

Tow/Haul Mode Light

and

Hill and Mountain Roads

Also see

“

Tow/Haul Mode

”

under

Driver Mode Control

Tow/Haul Mode Grade Braking

Tow/Haul Mode Grade Braking is only
enabled while the Tow/Haul Mode is
selected and the vehicle is not in the
Range Selection Mode. See

“

Tow/Haul

Mode

”

listed previously and

. Tow/Haul Mode Grade

Braking assists in maintaining desired
vehicle speeds when driving on
downhill grades by using the engine
and transmission to slow the vehicle.

To disable or enable Tow/Haul Grade
Braking within the current ignition
cycle, press and hold the Tow/Haul
button for five seconds. When the
button is released, the requested mode
change is made. A DIC message is
displayed.

See

Towing Equipment

For other forms of grade braking, see

Automatic Transmission

and

Cruise Control

Drive Systems

Four-Wheel Drive

If equipped, four-wheel drive engages
the front axle for extra traction.

Caution

Do not drive on clean, dry
pavement in 4

m

and 4

n

(if

equipped) for an extended period of
time. These conditions may cause
premature wear on the vehicle

’

s

powertrain.

Driving on clean, dry pavement in 4

m

or 4

n

may:

.

Cause a vibration to be felt in the
steering system.

.

Cause tires to wear faster.

.

Make the transfer case harder to
shift, and cause it to run noisier.

«
...
192
193
194
195
196
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Camcar Pages: 2

Brand: Vaisala Pages: 24

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

PRIME DESIGN HXR-269-E-UM3-80

Brand: Safe Fleet Pages: 12

Brand: Ferve Pages: 28

Brand: Metra Electronics Pages: 20

3 Facelift 2006

Brand: Mazda Pages: 94

Brand: Lexus Pages: 82

Even Brake 9400

Brand: Roadmaster Pages: 20

Brand: Nos Pages: 22

2001 Accord Sedan

Brand: Honda Pages: 372

Brand: Imiola HAK-POL Pages: 3

Brand: TrailFX Pages: 3

Brand: HawksHead Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands