Cadillac Escalade 2020 Owner'S Manual Download Page 124 | Manualshive

Page: 124 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

124

INSTRUMENTS AND CONTROLS

If the ABS warning light is the only
light on, the vehicle has regular
brakes, but ABS is not functioning.

If both the ABS warning light and the
brake system warning light are on,
ABS is not functioning and there is a
problem with the regular brakes. See
your dealer for service.

See

Brake System Warning Light

.

Sport Mode Light

This light comes on when Sport mode
is selected. See

Magnetic Ride Control

.

Tow/Haul Mode Light

For vehicles with the Tow/Haul Mode
feature, this light comes on when the
Tow/Haul Mode has been activated.

See

Tow/Haul Mode

Winter Driving Mode Light

This light comes on when Snow/Ice
mode is selected. See

Magnetic Ride

Lane Keep Assist (LKA)
Light

After the vehicle is started, this light
turns off and stays off if LKA has not
been turned on or is unavailable.

If available, this light is white if LKA
is turned on but not ready to assist.
This light is green if LKA is turned on
and ready to assist if the vehicle
crosses detected markings on one or
both sides of the lane.

LKA may assist by gently turning the
steering wheel if the vehicle
approaches a detected lane marking.
The LKA light is amber when
assisting.

This light flashes amber as a Lane
Departure Warning (LDW) alert, to
indicate that the lane marking has
been crossed.

«
...
122
123
124
125
126
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Porsche Pages: 192

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

BLADE-AL(TB)-TL2

Brand: iDataLink Pages: 9

Brand: Magneti Marelli Pages: 2

Brand: MAXWORKS Pages: 7

Brand: Fab Fours Pages: 13

Brand: Sagem Pages: 10

Brand: Fab Fours Pages: 21

1995 Cutlass Supreme

Brand: Oldsmobile Pages: 340

MAGICGRIP MGQDWD-CPO

Brand: Scosche Pages: 12

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

Brand: Volvo Pages: 7

Brand: MayPole Pages: 3

Brand: Toyota Pages: 204

Brand: Velleman Pages: 17

Brand: travall Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands