manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

119

Passenger Seat Belt Reminder
Light

There is a passenger seat belt
reminder light near the passenger
airbag status indicator. See

Passenger

Sensing System

0

71

.

When the vehicle is started, this light
flashes and a chime may come on to
remind passengers to fasten their seat
belt. Then the light stays on solid
until the belt is buckled. This cycle
continues several times if the
passenger remains or becomes
unbuckled while the vehicle is moving.

If the passenger seat belt is buckled,
neither the chime nor the light
comes on.

The front passenger seat belt reminder
light and chime may turn on if an
object is put on the seat such as a
briefcase, handbag, grocery bag,

laptop, or other electronic device. To
turn off the reminder light and/or
chime, remove the object from the
seat or buckle the seat belt.

Airbag Readiness Light

This light shows if there is an
electrical problem with the airbag
system. The system check includes
the airbag sensor(s), the passenger
sensing system, the pretensioners, the
airbag modules, the wiring, and the
crash sensing and diagnostic module.
For more information on the airbag
system, see

Airbag System

0

65

.

The airbag readiness light comes on
for several seconds when the vehicle is
started. If the light does not come on
then, have it fixed immediately.

{

Warning

If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in the
vehicle might not inflate in a crash,
or they could even inflate without a
crash. To help avoid injury, have
the vehicle serviced right away.

If there is a problem with the airbag
system, a Driver Information Center
(DIC) message may also come on.

Passenger Airbag Status
Indicator

The vehicle has a passenger sensing
system. See

Passenger Sensing System

0

71

for important safety information.

The passenger airbag status indicator
is in the overhead console.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Brand: Ultra-tow Pages: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Brand: Mercedes-Benz Pages: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Brand: Menabo Pages: 8
Camtree G-51 Instruction Manual preview
G-51
Brand: Camtree Pages: 5
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Brand: Mercedes-Benz Pages: 373
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Brand: Cadillac Pages: 34
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Brand: Cadillac Pages: 368
Luverne 205760 Installation Instructions preview
205760
Brand: Luverne Pages: 3
Navman B2+ User Manual preview
B2+
Brand: Navman Pages: 27
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Brand: STO N SHO Pages: 7
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Brand: TATA Motors Pages: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Brand: Safe Fleet Pages: 12
Big Mikes Performance Parts STO N SHO SNS 144 Installation Procedures Manual preview
STO N SHO SNS 144
Brand: Big Mikes Performance Parts Pages: 7
Lincoln MKZ 2018 Quick Reference Manual preview
MKZ 2018
Brand: Lincoln Pages: 10
C-KO RS-4-18-R-I Fitting Instructions preview
RS-4-18-R-I
Brand: C-KO Pages: 4
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Brand: Over Armour Offroad Pages: 9
rough country RCH5100 Installation Instructions preview
RCH5100
Brand: rough country Pages: 4
Volvo S40 2001 Owner'S Manual preview
S40 2001
Brand: Volvo Pages: 197

Brands by name

Popular brands

Load more brands