manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

301

Warning (Continued)

recommends it for the vehicle's tire
size combination and road
conditions. Follow that
manufacturer's instructions. To
avoid vehicle damage, drive slowly
and readjust or remove the traction
device if it contacts the vehicle. Do
not spin the wheels. If traction
devices are used, install them on
the rear tires.

If a Tire Goes Flat

It is unusual for a tire to blowout
while driving, especially if the tires are
maintained properly. If air goes out of
a tire, it is much more likely to leak
out slowly. But if there ever is a
blowout, here are a few tips about
what to expect and what to do:

If a front tire fails, the flat tire creates
a drag that pulls the vehicle toward
that side. Take your foot off the
accelerator pedal and grip the steering

wheel firmly. Steer to maintain lane
position, and then gently brake to a
stop, well off the road, if possible.

A rear blowout, particularly on a
curve, acts much like a skid and may
require the same correction as used in
a skid. Stop pressing the accelerator
pedal and steer to straighten the
vehicle. It may be very bumpy and
noisy. Gently brake to a stop, well off
the road, if possible.

{

Warning

Driving on a flat tire will cause
permanent damage to the tire.
Re-inflating a tire after it has been
driven on while severely
underinflated or flat may cause a
blowout and a serious crash. Never
attempt to re-inflate a tire that has
been driven on while severely
underinflated or flat. Have your
dealer or an authorized tire service
center repair or replace the flat tire
as soon as possible.

{

Warning

Lifting a vehicle and getting under
it to do maintenance or repairs is
dangerous without the appropriate
safety equipment and training. If a
jack is provided with the vehicle, it
is designed only for changing a flat
tire. If it is used for anything else,
you or others could be badly injured
or killed if the vehicle slips off the
jack. If a jack is provided with the
vehicle, only use it for changing a
flat tire.

If a tire goes flat, avoid further tire
and wheel damage by driving slowly
to a level place, well off the road,
if possible. Turn on the hazard
warning flashers. See

Hazard Warning

Flashers

0

151

.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Camcar 40000 Manual preview
40000
Brand: Camcar Pages: 6
Toyota 2011 Corolla LE Brochure preview
2011 Corolla LE
Brand: Toyota Pages: 19
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Brand: FORM FIT Pages: 2
Mazda 2 2016 Owner'S Manual preview
2 2016
Brand: Mazda Pages: 720
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
Marlon Xplore Pro II SxS Owner’S Manual Assembly & Installation Instructions preview
Xplore Pro II SxS
Brand: Marlon Pages: 15
Subaru 360 Sedan Service Manual preview
360 Sedan
Brand: Subaru Pages: 16
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Brand: mtf TRANSPORT SYSTEM Pages: 9
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
BMW 51 47 0 027 792 Installation Instructions Manual preview
51 47 0 027 792
Brand: BMW Pages: 7
Ford 2007 Navigator (Spanish) Owner'S Manual preview
2007 Navigator
Brand: Ford Pages: 728
Westin 58-53935 Installation Instructions preview
58-53935
Brand: Westin Pages: 5
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Brand: BENDIX Pages: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Brand: Toyota Pages: 56
J. Strong JST506BT Installation Instructions preview
JST506BT
Brand: J. Strong Pages: 2

Brands by name

Popular brands

Load more brands