Cadillac Escalade 2020 Owner'S Manual Download Page 268 | Manualshive

Page: 268 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

268

VEHICLE CARE

Do not top off the brake fluid. Adding
fluid does not correct a leak. If fluid is
added when the linings are worn,
there will be too much fluid when
new brake linings are installed. Add or
remove fluid, as necessary, only when
work is done on the brake hydraulic
system.

{

Warning

If too much brake fluid is added, it
can spill on the engine and burn,
if the engine is hot enough. You or
others could be burned, and the
vehicle could be damaged. Add
brake fluid only when work is done
on the brake hydraulic system.

When the brake fluid falls to a low
level, the brake warning light comes
on. See

Brake System Warning Light

.

Brake fluid absorbs water over time.
Replace brake fluid at the specified
intervals to prevent increased
stopping distance. See

Checking Brake Fluid

Check brake fluid by looking at the
brake fluid reservoir. See

Compartment Overview

.

The fluid level should be above MIN.
If it is not, have the brake hydraulic
system checked to see if there is
a leak.

After work is done on the brake
hydraulic system, make sure the level
is above MIN but not over the
MAX mark.

What to Add

Use only GM approved DOT 3 brake
fluid from a clean, sealed container.
See

Recommended Fluids and

{

Warning

The wrong or contaminated brake
fluid could result in damage to the
brake system. This could result in
the loss of braking leading to a
possible injury. Always use the
proper GM approved brake fluid.

Caution

If brake fluid is spilled on the
vehicle's painted surfaces, the paint
finish can be damaged. Immediately
wash off any painted surface.

Battery

The original equipment battery is
maintenance free. Do not remove the
cap and do not add fluid.

«
...
266
267
268
269
270
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

1973 Convertible

Brand: Volkswagen Pages: 80

Brand: Gatorback Mudflaps Pages: 4

Brand: METRON Pages: 4

2013 GMC Savana

Brand: GMC Pages: 398

Brand: Bilstein Pages: 7

Brand: Rydeen Pages: 14

MAGICGRIP MGQDWD-CPO

Brand: Scosche Pages: 12

Multi Vehicle Mount MVM-35-05

Brand: Bracketron Pages: 4

Brand: Quadratec Pages: 8

Brand: travall Pages: 4

Brand: chinavasion Pages: 3

Brand: Lincoln Pages: 370

Forester 2.5X 2003

Brand: Subaru Pages: 44

Brand: Prorack Pages: 14

Brand: VanEssa mobilcamping Pages: 12

Brand: Thule Pages: 1

SnowDrive Pilot-Pro 16270

Brand: Lampa Pages: 32

Brand: Thule Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands