Cadillac Escalade 2020 Owner'S Manual Download Page 240 | Manualshive

Page: 240 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

240

DRIVING AND OPERATING

2. Slowly back down the boat ramp

until the boat is floating, but no
further than necessary.

3. Press and hold the brake pedal,

but do not shift into P (Park) yet.

4. Have someone place chocks

under the front wheels of the
vehicle.

5. Gradually release the brake pedal

to allow the chocks to absorb the
load of the trailer.

6. Reapply the brake pedal. Then

apply the parking brake and shift
into P (Park).

7. Release the brake pedal.

Pulling the Trailer from the Water

1. Press and hold the brake pedal.

2. Start the engine and shift into

a gear.

3. Release the parking brake.

4. Let up on the brake pedal.

5. Drive slowly until the tires are

clear of the chocks.

6. Stop and have someone pick up

and store the chocks.

7. Slowly pull the trailer from the

water.

8. Once the vehicle and trailer have

been driven from the sloped part
of the boat ramp, the vehicle can
be shifted from four-wheel-drive
high. Shift into the drive mode
that is appropriate for the road
conditions.

Caution

If the vehicle tires begin to spin and
the vehicle begins to slide toward
the water, remove your foot from
the accelerator pedal and apply the
brake pedal. Seek help to have the
vehicle towed up the ramp.

Maintenance when Trailer
Towing

The vehicle needs service more often
when used to tow trailers. See

Maintenance Schedule

. It is

especially important to check the
automatic transmission fluid, engine

oil, axle lubricant, belts, cooling
system, and brake system before and
during each trip.

Check periodically that all nuts and
bolts on the trailer hitch are tight.

Engine Cooling when Trailer
Towing

The cooling system may temporarily
overheat during severe operating
conditions. See

Engine Overheating

Trailer Towing

Caution

Towing a trailer improperly can
damage the vehicle and result in
costly repairs not covered by the
vehicle warranty. To tow a trailer
correctly, follow the directions in
this section and see your dealer for
important information about
towing a trailer with the vehicle.

«
...
238
239
240
241
242
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Q'STRAINT Pages: 10

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Brand: Roav Pages: 10

Brand: Toyota Pages: 35

Brand: Haibang Pages: 6

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: Audiovox Pages: 3

Brand: Victory 4x4 Pages: 9

Brand: Improved Racing Pages: 17

Brand: TAUBENREUTHER Pages: 18

Brand: Xpresskit Pages: 12

Performer-Plus 2172

Brand: Edelbrock Pages: 4

Brand: Volvo Pages: 16

Brand: TATA Motors Pages: 146

CommCenter 300MB-SD

Brand: Federal Signal Corporation Pages: 60

Install Essentials CAN1

Brand: Directed Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands