manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

264

VEHICLE CARE

3. Fill the coolant surge tank with

the proper mixture to the full
cold mark.

4. With the coolant surge tank

pressure cap off, start the engine
and let it run until the engine
coolant temperature gauge
indicates approximately 90 °C
(195 °F).

By this time, the coolant level
inside the coolant surge tank
may be lower. If the level is
lower, add more of the proper
mixture to the coolant surge
tank until the level reaches the
full cold mark.

5. Replace the pressure cap tightly.

6. Verify coolant level after the

engine is shut off and the
coolant is cold. If necessary,
repeat coolant fill procedure
Steps 1-6.

Caution

If the pressure cap is not tightly
installed, coolant loss and engine
damage may occur. Be sure the cap
is properly and tightly secured.

Engine Overheating

Caution

Do not run the engine if there is a
leak in the engine cooling system.
This can cause a loss of all coolant
and can damage the system and
vehicle. Have any leaks fixed
right away.

The vehicle has several indicators to
warn of engine overheating.

There is a coolant temperature gauge
in the vehicle's instrument cluster. See

Engine Coolant Temperature Gauge

0

118

.

In addition, there are ENGINE
OVERHEATED STOP ENGINE,
ENGINE OVERHEATED IDLE ENGINE,

and ENGINE POWER IS REDUCED
messages in the Driver Information
Center (DIC).

If the decision is made not to lift the
hood when this warning appears, get
service help right away.

If the decision is made to lift the
hood, make sure the vehicle is parked
on a level surface.

Check to see if the engine cooling
fan(s) are running. If the engine is
overheating, the fans should be
running. If they are not, do not
continue to run the engine, and have
the vehicle serviced.

If Steam is Coming from the
Engine Compartment

{

Warning

Steam and scalding liquids from a
hot cooling system are under
pressure. Turning the pressure cap,
even a little, can cause them to
come out at high speed and you
could be burned. Never turn the cap

(Continued)

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Brand: IAME Pages: 17
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Brand: FORM FIT Pages: 2
Edelbrock Chevrolet 5783 Installation Instructions preview
Chevrolet 5783
Brand: Edelbrock Pages: 1
FORM FIT 1308 Installation Instructions preview
1308
Brand: FORM FIT Pages: 2
Skoda Fabia Combi 5J Fitting Instructions preview
Fabia Combi 5J
Brand: Skoda Pages: 2
Jeep WRANGLER 2017 User Manual preview
WRANGLER 2017
Brand: Jeep Pages: 292
RBO IT FITS RBO1018 Product Manual preview
IT FITS RBO1018
Brand: RBO Pages: 36
Whispbar K482W Fitting Instructions Manual preview
K482W
Brand: Whispbar Pages: 14
Advent MAZBTSW2 Owner'S Manual preview
MAZBTSW2
Brand: Advent Pages: 8
Prorack K671 Fitting Instructions Manual preview
K671
Brand: Prorack Pages: 17
Air Lift 75524 Installation Manual preview
75524
Brand: Air Lift Pages: 24
Kia quoris Manual preview
quoris
Brand: Kia Pages: 522
Pyle PLCAP50R Manual preview
PLCAP50R
Brand: Pyle Pages: 4
Toyota 2009 Highlander Quick Reference Manual preview
2009 Highlander
Brand: Toyota Pages: 19
HUSKY LINERS 4707 Installation Manual preview
4707
Brand: HUSKY LINERS Pages: 3
Toyota PC162-0K00H Installation Manual preview
PC162-0K00H
Brand: Toyota Pages: 5
gdw 1180 Fitting Instructions Manual preview
1180
Brand: gdw Pages: 8
Sena 50S Quick Start Manual preview
50S
Brand: Sena Pages: 2

Brands by name

Popular brands

Load more brands