Cadillac Escalade 2020 Owner'S Manual Download Page 289 | Manualshive

Page: 289 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

289

Low-Profile Tires

The vehicle has low profile tires
that are classified as touring tires
and are designed for on road use.
The low-profile, wide tread design
is not recommended for off-road
driving. See

Off-Road Driving

,

for additional information.

Caution

Low-profile tires are more
susceptible to damage from road
hazards or curb impact than
standard profile tires. Tire and/or
wheel assembly damage can occur
when coming into contact with
road hazards like potholes, or sharp
edged objects, or when sliding into
a curb. The warranty does not cover
this type of damage. Keep tires set
to the correct inflation pressure and
when possible, avoid contact with
curbs, potholes, and other road
hazards.

All-Terrain Tires

This vehicle may have all-terrain tires.
These tires provide good performance
on most road surfaces, weather
conditions, and for off-road driving.
See

Off-Road Driving

.

The tread pattern on these tires may
wear more unevenly than other tires.
Consider rotating the tires more
frequently than at 12 000 km
(7,500 mi) intervals if irregular wear is
noted when the tires are inspected.
See

Tire Inspection

.

Tire Pressure

Tires need the correct amount of
air pressure to operate effectively.

{

Warning

Neither tire underinflation nor
overinflation is good.
Underinflated tires, or tires that
do not have enough air, can
result in:

(Continued)

Warning (Continued)

.

Tire overloading and
overheating which could
lead to a blowout.

.

Premature or

irregular wear.

.

Poor handling.

.

Reduced fuel economy.

Overinflated tires, or tires that
have too much air, can result in:

.

Unusual wear.

.

Poor handling.

.

Rough ride.

.

Needless damage from
road hazards.

The Tire and Loading Information
label on the vehicle indicates the
original equipment tires and the
correct cold tire inflation
pressures. The recommended
pressure is the minimum air

«
...
287
288
289
290
291
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Kargo Master Pages: 5

Brand: 3SIXT Pages: 12

Brand: AMP Research Pages: 12

Half Size Trunk Box Organizer C-TBO-CV

Brand: Havis-Shields Pages: 1

Brand: Volvo Pages: 8

Brand: Cadillac Pages: 407

Brand: Hyundai Pages: 19

Brand: E&G Classics Pages: 4

Brand: Gator Pages: 6

Brand: F.lli Menabo Pages: 16

MagicSpeed MS900

Brand: Waeco Pages: 120

Brand: Yakima Pages: 11

2011 Camry SE V6

Brand: Toyota Pages: 33

Brand: Porsche Pages: 1005

Brand: Ford Pages: 17

Brand: Kuda-Phonebase Pages: 3

Brand: Hyundai Pages: 7

Brand: HaWeKo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands