URAL Motorcycles 4320M Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 92

91

Bead and lock rings of the wheels are mounted in the certain position with the help of lock

ring welded to the rim, and the extrusion B (see figure 75) on the lock ring entering the corresponding
hole (slot) A of the bead ring. The second slot of the bead ring is used for wheels disassembly. One of
lock ring ends has a slot to grasp the ring when it is removed from the rim lock groove.

Lock ring stop plate serves to prevent ring barring during operation, when the truck is run-

ning with low air pressure in the tires and also serves as a bracket where wheel valve 1 (see Figure
72) is fixed and additional support for air inlet hoses protection cases.

The wheel valve is mounted on 254Г-508 wheel from the outer side of stop bracket, and on

533-310 and 400Г-508 wheels - from the inner side.

Rubber seal 9 of wheel vent slot prevents tire internals from dirt and ensures chamber valve

installation in certain position.

Wheels retaining nuts and pins from right and left sides have right-hand thread.

Tire and Wheel Maintenance
Most completely wheel and tire resource utilisation and their safe operation can be en-

sured only at regular maintenance and compliance with tire operation requirements, road safe-
ty rules requirements, health and safety requirements of motor vehicles.

The following requirements must be observed:
-Strictly comply with load norms and tire air pressure norms;
-Maintain wheels and tires on time;

1-Wheel valve; 2-rim base with disc; 3-lock ring
stop plate; 4-lock ring; 5-bead ring; 6-tire; 7-
inner tube; 8-tire flap; 9-vent slot seal

Figure 72 - Wheel with Tire Assembly

«
...
90
91
92
93
94
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов