URAL Motorcycles 4320M Скачать руководство пользователя страница 46

Страница: 46 / 321

Table 10 - State Indication of User Interface Unit

User interface unit state

“SOS” button light

(white/red)

“Service” button

light

(white/yellow)

Indicator state

Indication (switching on)

White

Red is on for five sec,

then green flashes

“ERA” mode

White

Green flashes

“Emergency call” mode

Red

White

Green is on

Test mode

Red

Yellow

Yellow is on

Malfunction, internal storage
is full

White

Red is on

Emergency call is impossible

White

Red is on

Redial in “Emergency call”
mode

Red is flashing

White

Green is on

Transfer of minimum infor-
mation in “Emergency call”
mode

Red is flashing

White

Green is on

Voice connection in “Emer-
gency call” mode

Red is on

White

Green is on

Reserve battery is discharged
below set parameter

White

Yellow is flashing

No GLONASS/GPS signals

White

Yellow is on

No GPS signals

White

Red is on

If the system detected any malfunction of installed components, contact your regional

service centre (read www.santel-navi.ru).

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 46 / 321

Результаты поиска

Содержание 4320M

Отзывы: