URAL Motorcycles 4320M Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 70

69

4.2.4.2 Transmission Devices Control

is remote, electrical and pneumatic, consisting of

the transfer box gears shifting mechanism, the transfer box differential lock mechanism, the addi-
tional power takeoff switch*; power takeoff switch*; the cross-axle differential lock mechanism
of the medium and the rear axles, solenoid valves installed on the right frame girder, pipelines and
switches in the cab.

Electric and pneumatic control scheme of transmission devices is given in figure 52.

1-non-brake consumer tank; 2-transfer box differential lock mechanism; 3-transfer box gears
shifting mechanism; 4-additional power takeoff switch; 5-power takeoff switch; 6 and 7-the cross-
axle differential lock mechanism of the intermediate and the rear axles.
solenoid valves: A-transfer box differential lock; B-neutral; C-low speed; D-hight speed; E-
additional power takeoff*; F-power takeoff*; G-the cross-axle differential lock*; a-air supply; b-
for switching on.

Figure 52 - Electric and Pneumatic Control Scheme of Transmission Devices

When pressing the transfer box gear shift, the necessary gear is selected on the cab switch

board (has three fixed positions: high speed, neutral, low speed), but the gears are not shifted. To
shift the gear, press the transfer box gear switch button and hold it for 5...7 seconds, herein sole-
noid valves will supply air to the transfer box gears shifting mechanism and the gears are shifted.

______________
*Installed as an option

«
...
68
69
70
71
72
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов