URAL Motorcycles 4320M Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 3

2

The Manual is dedicated for drivers and motor transport workers connected with Ural

tucks operation. The Manual gives technical specifications of the trucks, short description of their
construction and operation of truck components, their adjustment and maintenance, reference da-
ta.

Due to constant modernisation of the product improving its reliability and operation con-

ditions, the construction may be partially amended, and such amendments are not included in this
Manual.

When operating URAL truckswith 4х4, 6х6 wheel arrangement and its modification with

“Euro-4” engines and pneumatic brake system drive the following should be used:

Operation Manual “Ural-4320M trucks and its Modifications”;
Operation Manual “YAMZ-536, YAMZ-5362, YAMZ-5362, YAMZ-5363, YAMZ-5364

Engines”

Operation Manual for ZF 9S 1310 Gearbox (for power units with ZF gearbox);
Operation Manual for YAMZ-0905 Gearbox (for power units with YAMZ-0905 gear-

box);

Operation Manual for YAMZ-1105 Gearbox (for power units with YAMZ-1105 gear-

box);

Operation Manual for

9JS135ТА

Gearbox (for power units with FAST GEAR gearbox).

Operation Manual for the Engine Starting Heater;
Operation Manual (Instruction) for “Lead-acid, starter Storage Batteries”)
Installation and Operation Manual for Drawbar Coupling;
Operation Manual “URAL 73.3801-01 Combination of Devices” АДИГ.453895.012РЭ

Элара.

The Tachograph Installation and Operation Manual.

In the second edition of the Operation Manual amendments relating to the tachograph in-

stallation (Chapter “Control Tools and Devices”); regulation of transfer box (Chapter “Transmis-
sion” paragraph “Transfer Box”); maintenance intervals (Chapter “Maintenance”, paragraphs
“List of Trucks Maintenance Operations”, “Lubricants and Hydraulic Fluids Charts”) are made.

The Manual is compiled by the engineers of the Engineering Design Department of OJSC “URAL
Motor Vehicles Plant” Kochetkov A.L., Karkavin V.I., Kirdyashkin A.N., Kropotov A.N., Polen-
kov A.A., Pushkin Yu.A., Rybalkin D.A., Smirnov I.G., Savanovich V.P., Sokolov A.P., Sokolov
O.V., Trofimov V.A., Shevchenko S.V., Maltsev A.V. Under the general management of the
Chief Designer for Commercial Vehicles Zakharik A.M.

Draftsman: Petrova N.A.
Publishing Editor: Trofimov V.A.

«
1
2
3
4
5
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов