URAL Motorcycles 4320M Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 88

87

Axle upstroke is restricted by rubber buffers 9 fastened to the bottom spar cap. Axle down

stroke is restricted by spring end jamming in the support bracket 6.

Truck suspension with various load to the rear bogie differs by springs and u-bolt length.

1,8-Spring  brackets  (front,  rear);  2-auxiliary  spring  bracket;  3-auxiliary  spring;  4-spring  u-bolt;  5-trim;  6-
block; 7,24-shock absorber brackets (upper, lower); 9-spring; 10-shock absorber; 11-shock absorber retaining
nut; 12-washer; 13-shock absorber bushings; 14-buffer retaining nut; 15-buffer; 16-spring support bracket; 17-
bush (upper, lower); 18-distance piece; 19-bracket tie bolt; 20-stud;  21-eye u-bolt; 22-eye u-bolt nut; 23-eye
trim;  25-shock  absorber  bracket  fixing  bolt;  26-u-bolt  nut;  27-seal;  28,29-bracket  lid  fixing  bolts;  30-spring
eye bolt nut; 31-spring eye fixing nut; 32-spring eye; 33-front bracket lid; a = 1-2.5 mm, b = 1-2 mm

Figure 70 - Rear Suspension of Trucks with 4x4 Wheel Arrangement

«
...
86
87
88
89
90
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов