URAL Motorcycles 4320M Скачать руководство пользователя страница 169

Страница: 169 / 321

4.7.1.2 Doors of the cabover truck

are shown in figure 133. Doors are equipped with

locks for locking doors. Outside the door is locked with the key, inside – with the blocking button.

When opening the door, the automatic switch-on of the cabin indoor light above the driver

and the passenger upon the correspondent position of the master lighting switch.

Windows are equipped with drop and swinging windows. Drop windows lift and decrease

by lifting devices. Windows shall move in the directions freely without jawings.

164

1-power window handle; 2-opening door handle;
3-closing door handle; 4-button for door blocking
from inside

Figure 132 - Conventional cabin doors

1-vent window catch lever; 2-power window
handle; 3-opening door handle; 4-closing door
handle; 5-button for door blocking from inside

Figure 133

–

Door of the cabover truck

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 169 / 321

Результаты поиска

Содержание 4320M

Отзывы: