URAL Motorcycles 4320M Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 7

6

- Trade mark of the manufacturer;
- Identification number;
- Modification;
- gross vehicle weight rating;
- gross axle weight rating;
- gross road-train weight rating;
- gross fifth-wheel coupling load rating;
- Approval number of vehicle type (approval of chassis type).
Identification number is marked on the right frame girder in rear part.
Vehicle identification number structure and contents:

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Х

1

Р

*

*

*

*

*

*

*

*

*

*

*

*

*

*

______________

*Variable information

Pos. 1-3:

Х1Р

- manufacturer's international identification code (WMI) -

OJSC “The Automobile Plant “Ural”

Pos. 4-9: type and modification identification:
432000 is for 4320-?-7?
43203? is for 43203-1151-71,
432060 is for 43206-?11-71,
442020 is for 44202-0?11-7?,
555700 is for 5557-?-7?
555710 is for 55571-???1-7?
Pos. 10: Manufacturing year code
Pos. 11-17: Vehicle plant number
Figures used for identifying manufacturing year:

В - 2011, С - 2012, D - 2013, Е - 2014.

Cab and engine are marked as components according to OST 37.001.269-96.
Cab as a vehicle component is marked on the right side as viewed in the direction of ve-

hicle motion in the lower part of the door opening. The marking includes 14 signs.

Information on the engine marking is given in the Operation Manual for “YAMZ-536,

YAMZ-5361, YAMZ-5362, YAMZ-5363, YAMZ-5364 Engines”.

The table with the conformity mark is located close to the manufacturer’s plate.

«
...
5
6
7
8
9
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов