URAL Motorcycles 4320M Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 76

75

Table 11

Axle ratio

Marks on the butt of the driving

cylindrical pinion from

the conical gear side

Mark on the idler gear

7.49

No marking

One drill under the crown 5 mm long and 3
mm deep

6.77

Three 10 mm holes on the 65 mm
journal butt 2 mm deep

Two drills under the crown 5 mm long and
3 mm deep at the distance of 10 mm

Eleven bolts and pins are installed outside, and two bolts are installed in the conical

gears chambers. Internal bolts can be accessed only when the side lid 6 is removed. Spring wash-
ers are installed under the outer bolts and pin nuts. Internal bolts are forelocked with wire.

Main gear wheels and bearings are oiled with the axle case oil going through the main

gear crankcase up to the inspection door level. The oil is captured by the wheels and goes to the
main gear crankcase chamber through the roller bearing 2, and then it flows to the axle case. Con-
ical pinion bearings are oiled from the conical gears chamber, oil then goes to the bushing sleeve
through the crankcase cover tray and oil feeding connector.

1-Air supply gaskets; 2-wedger; 3-brake drum; 4-axle shaft; 5-spring mountain bracket; 6-crankcase cover;
7,9-seals; 8-main gear; 10-axle case; 11-drain plug; 12-differential axle case

Figure 60 - Rear Driving Axle

4.2.6.2 Intermediate and Rear Axles

. Cross-axle differentials with positive locking*

are installed on the medium and rear (see figure 61).

*

Installed on request.

«
...
74
75
76
77
78
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов