URAL Motorcycles 4320M Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 162

4.7 Cab, Trim Package and Platform

4.7.1 Cab

The cab of the cabover truck - two-seat, spring-mounted, equipped with the heat and

sound  insulation,  the  spring-mounted  driver  seat  and  the  passenger  seat,  the  ventilation  system,
the  heating  system  and  the  heating  system  of  windshields,  the  vehicle  sun  roof,  sunscreens,  the
wind  shield  wiper,  the  windshield  washer,  rear  view  mirrors,  side  view  mirrors  and  wide-angle
mirrors, and also the forward view mirror and could be completed with the independent heating
unit.

The independent air heating unit Planar-4D-24 (or Airtronic D2 or D4) is located inside

the cab and on the right side as viewed in the direction of the truck motion. Fuel supply is provid-
ed out of the fuel tank.

Upon operation of the independent heating unit, it is necessary to follow requirements,

specified in the paragraph “Safety Requirements”.

Regulate spherical mirrors, providing the viewing area though them according to figures

124, 125, 126, 127, by loose tension bolts of holders and mirrors, and them fasten them properly.

1,4-rear view mirrors (right, left); 2-viewing area of road surface; 3-point of driver

’

s eyes

Figure 124 - Viewing area through outside rear view mirrors (II class)

1,4-wide-angle mirrors (on one holder of the II class); 2-viewing area of road surface; 3-point of driver

’

s

eyes

Figure 125 - Viewing area through wide-angle mirrors (IV class)

159

«
...
160
161
162
163
164
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов