URAL Motorcycles 4320M Скачать руководство пользователя страница 225

Страница: 225 / 321

Scope of work

Technical specifications

Recommended equip-

ment, devices and tools

Axle configura-

tion

4х4

6х6

in storage batteries, if nec-
essary, add distilled water.

for storage batteries

distilled water, glass
tube with the diameter
3-5 mm

Check fastening and re-

liability of the contact and
clearness of cable terminal
to starter terminal and stor-
age batteries.

Fastening of cable terminal

should be reliable.

Wrenches

14x17,

17x19

Check and, if neces-

sary, adjust lights (see sub-
paragraph “Lighting and
Alarm System”)

Adjust lights when the truck

is not loaded, located on the
level ground.

Screwdriver, screen

with special line pat-
tern

Check fastening relia-

bility of electrical wire har-
ness.

Loosening of the wire fas-

teners is not allowed.

Pliers, screwdriver,

knife, adhesive tape

Check fastening of the

storage batteries container
mounting bracket to the
frame.

The same

Wrenches

17x19,

22x24

Check the condition of

the  rubber  boot  on  rear
lights,  side  repeaters,  the
storage  battery  switch,  the
stop  signal,  the  fuel  level
sensor, the secondary brake
switch.

Loosening of the wire fas-

teners is not allowed.

Visual examination

Dedicated Equipment

Check

fastening

crankcase

mounting

ar-

rangement  of  the  power
takeoff device (PTO) to the
gearbox  housing  and  fas-
tening  of  the  oil  pump  to
the crankcase of PTO.

Loosening of the fasteners is
not allowed.

Wrench 14x17

Lubrication

Maintain the engine in

accordance with operating
manual for the engine

207

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 225 / 321

Результаты поиска

Содержание 4320M

Отзывы: