URAL Motorcycles 4320M Скачать руководство пользователя страница 118

Страница: 118 / 321

115

According to Figure 86:

- tighten the bolt 5 with 75-85 Nm (7.5-8.5 kgfm) torque. Lubricate “d” surface with

АМС-3 grease - GOST 2712-75

- before assembling lubricate “g” surface of axis 7 and “f” surface of brake pads with

graphite grease - GOST 3333-80. Lubricate “e”, “h” and “p” surfaces with АМС-3 grease - GOST
2712-75.

Tightening scheme for brake pad axes nuts: first tighten nut 6 with 431-490 Nm (44-50

kgfm) torque, then nut 11 with 274-313 Nm (28-32 kgfm).

If the drum is worn, if there are annular grooves deeper than 1mm, bore drum work sur-

face according to Table 13, basing on outer hub bearing rings (see Figure 94). Drum work surface
runout should not exceed 0.25 mm.

Table 13 - Brake Drum Internal Surface Diameter After Boring

Diameter after first

boring, mm

Diameter after second

boring, mm

Maximal diameter of

boring, mm

421.5

423

424.38

4.5.1.5 Speed Sensor.

Brakes of front and rear wheels have inductive sensors 2 (see Fig-

ure 95).

1-Cap; 2-inductive sensor; 3-clamping sleeve; 4-sensor target gear ring; 5-wheel hub; 6-rubber bushing

Figure 95 - Speed Sensor

A, B - base surfaces

Figure 94 - Brake Drum Adaptation Scheme

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 118 / 321

Результаты поиска

Содержание 4320M

Отзывы: