URAL Motorcycles 4320M Скачать руководство пользователя страница 235

Страница: 235 / 321

Scope of work

Technical specifications

Recommended equipment,

devices and tools

Axle configu-

ration

4х4

6х6

Check tightening and,

if  necessary,  tighten  up
retaining  nuts  (upon  every
sixth  Maintenance-15000)
of:

- universal shafts;
- lever, upper and low-

er covers of axle swivels
and ball unit flanges.

Loosening of the fasteners is

not allowed.

The same

Box wrench 24x27

The same

Check tightening and,

if necessary, tighten up
bolt and fastening nuts of
leading axles drive gears.

The same

Wrench

22x24,

box wrench 22x24, pli-
ers, screwdriver

Undercarriage

Check and, if neces-

sary, tighten nuts of:

- Wedges of fixation

of front spring pins;

Loosening of the fasteners is

not allowed.

Wrench 17x19

- Front spring eye;

The same

Socket wrench 30x32,

tire iron with jack handle

- Rear spring eye (for

trucks 4х4);

-«-

The same

- U-bolt of front spring

eye;

-«-

Box wrench 22х24

- U-bolt of rear spring

eye (for trucks 4х4);

-«-

The same

- Front spring U-bolt;

Loosening of the fasteners is

not allowed. Tighten the truck
with full load.

Socket wrench 30x32

for spring U-bolt nuts, tire
iron with hydraulic jack
handle

- Rear spring U-bolt;

Loosening of the fasteners is

not  allowed.  Tighten  the  truck
with  full  load  (for  trucks  4х4),
and  for  trucks  6х6  tighten  the
non-loaded truck.

Socket wrench 27x38

for wheel nuts, tire iron
with hydraulic jack han-
dle

212

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 235 / 321

Результаты поиска

Содержание 4320M

Отзывы: