URAL Motorcycles 4320M Скачать руководство пользователя страница 196

Страница: 196 / 321

190

Failure

Possible cause

Troubleshooting practice

Steering wheel

Unstable truck move-

ment,

Steer unfastening

Fasten the crankcase and steer

bracket retaining nuts

“Hard” steering wheel

Air or water in the system

(foam in the tank, cloudy oil)

Discharge air If the air is not dis-

charged, check tightening of all
hydraulic joints, replace the filter If
the above measures did not help,
change the oil.

The pump does not operate

with necessary capacity and pres-
sure

Check pump pressure

Steering shaft crankcase spline

joint is not flexible

Disassemble, clean and lubricate

Oil throwing from the oil

tank through the breather

Filter clogging

Replace the filter

Brake System

Minimal air pressure emer-

gency indicator is permanently
flashing (when the engine is
stopped)

No air due to compressor

failure, pressure controller fail-
ure, or pneumatic system leak-
age

Repair the compressor, replace

the pressure controller. Find air
leakage place and repair

Braking is not efficient

Piston seals or air-oil intensi-

fier  insert  seal  are  worn,  herein
air  is  discharging  from  the  air-
oil  intensifier  exhaust  pipe,
when the brake pedal is pressed

Replace the seals

The brakes are stuck (are

not released)

There is no brake pedal free

travel

Adjust brake pedal free travel

Pressure controller is often

actuated

Compressed air leakage in

the system from the controller to
the safety valves unit

Fasten the joints, replace defec-

tive joint parts, pipelines

Storage Batteries

The storage battery does

not provide sufficient torque of
the engine crankshaft

Low battery

(below permissible level)

High voltage drop in stator

feeding circuit

Charge the battery and check al-

ternator and voltage regulator oper-
ability

Clean battery clips and clamps.

Lubricate them with jelly. Tighten
stator clamps fixation, if necessary.

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 196 / 321

Результаты поиска

Содержание 4320M

Отзывы: