URAL Motorcycles 4320M Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 137

134

1-Vehicle communication interface (VCI); 2-ignition switch; 3-fuses; 4-warning lamp; 5-test switch; 6-key
phasers; 7-front right modulator; 8-rear right modulator; 9-rear left modulator; 10-front left modulator

Figure 115 - Plug Connection Scheme of Knorr Bremze Control Unit

Error codes are activated by one click on ABS test button 1 (see Figure 114) for

conventional cab trucks and ABS test button 10 (see Figure 32) for cabover trucks during
0.5-8 sec, and they are displayed by warning lamp flashing (the so called blink codes are de-
livered) (see Figure 116).

Figure 116 - Error Codes (Blink Codes) Activation

Each error is delivered in a block consisting of two categories: first identifies com-

ponent number and second one - error number.

Error codes are given in Table 14.
Error codes delivery can be interrupted by clicking again ABS test button 1 (see Figure

114) for conventional cab trucks and ABS test button 10 (see Figure 32) for cabover trucks.

«
...
135
136
137
138
139
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов