URAL Motorcycles 4320M Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 227

Scope of work

Technical specifications

Recommended equipment,

devices and tools

Axle configu-

ration

4х4

6х6

Replace oil in the

gearbox YAMZ-0905 or
YAMZ-1105 with cleaning
of the crankcase, the screen
and the magnet.

Oil level in the gearbox

housing  should  be  not  lower
than the lower edge of the check
hole.  When  installing  the  entry
cover,  be  attentive  not  to  shut
down the oil passage with cover
or  its  filler.  Clean  the  gearbox
with the industrial oil И-12А or
И-20А  upon    GOST  20799-88;
2,5-3  l.  Cleaning  of  the  gearbox
with kerosene or diesel oil is strict-
ly  forbidden  for  the  avoidance  of
malfunctions  upon  the  oil  pump
performance  due  to  insufficient
depression  during  intake  and  as  a
consequence  breakdown  of  the
gearbox.

Wrench 14х17, tank

for pure oil and tank for
used oil.

+

+

Replace oil in the gear-

box FG9JS135

Oil level in the gearbox

housing should be not lower
than the lower edge of the check
hole.

Wrench 22

+

+

Check oil level in the

gearbox ZF 9S1310

Oil level in the gearbox

housing should be not lower
than the lower edge of the check
hole.

Wrench 22

+

+

Replace oil:
- in the transfer box hous-

ing

(see

subparagraph

“Transmission” and Lubri-
cants and Hydraulic Fluids
Charts);

Pour oil to the level of the

level-fill  opening  of  the  rear
crankcase  side.  Oil  leakage
through plugs is not allowed.

Wrench 27x30, tank

for scavenge oil., oil dis-
penser of 133М model,
waste cloth

+

+

- in the bevel gear hous-

ing of drive axles.

Pour oil to the level-fill

opening on the axle housing.

If the bevel gear is dis-

mounted, fill preliminary 1 liter
of oil through the hole for
breather on the bevel gear hous-
ing, the rest – through the level-
fill opening up to its edge.

Wrench 27x30, tank

for scavenge oil., oil dis-
penser of 133М model,
waste cloth

+

+

208

«
...
225
226
227
228
229
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов