URAL Motorcycles 4320M Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 321

URAL Motorcycles 4320M Скачать руководство пользователя страница 58

57

Exit from the adjustment mode is possible with saving maximum rpm of 1000 rpm, for

that hold the switch 6 (see figure 32) for about 5 seconds. The pre-set value (1000 rpm maximum)
of the engine idle will be saved in the engine electronic control unit and will be recorded to the
electronic control unit memory after cutting off the ignition in standard mode (power supply for
the electronic control unit continues after the ignition is cut off for minimum 30 seconds). Next
engine start idle value will come back to the pre-saved value. To restore minimal engine idle rpm
repeat the adjustment mode with saving 700 rpm value.

Exit from the adjustment mode without saving new value of engine idle rpm can be done

in two ways:

- press the accelerator pedal (by increasing rpm for more than 1500 rpm);
- stop the engine.

«
...
56
57
58
59
60
...
»

Содержание 4320M


































































































































































































































































































































Отзывы:

Нет отзывов