URAL Motorcycles 4320M Скачать руководство пользователя страница 197

Страница: 197 / 321

191

Failure

Possible cause

Troubleshooting practice

Fast battery self-discharge

Failure of all

or several storage batteries

Battery leads are dirty with

mud or battery fluid covering
the battery surface

Give the battery for repair

Clean the battery with dry cloth,

then with a cloth moisten in 10%
ammonia spirit solution or soda ash
solution

Battery fluid has contami-

nants

Discharge the battery with cur-

rent, equal to 1

⁄

10 of storage capac-

ity, until 1.1-1.2 V for one battery.
Drain battery fluid, fill new battery
fluid and charge the battery

Battery fluid is decreased

too fast

Battery fluid is “boiling out”

Battery monoblock is dam-

aged

Check the voltage regulator
Give the battery for repair

Battery fluid is leaking

from one or two batteries
through the vent hole during
battery charge

Too high battery fluid level
Too high charge rate

Short circuit of the plates in

one of the batteries

Remove excess battery fluid

with rubber bulb

Check the voltage regulator
Give the battery for repair

When charging completely

discharged battery, battery fluid
voltage  and  temperature  are
raising  very  fast  and  boiling
starts,  and  density  is  slightly
increasing

Sulfatation of the plates that

can be caused by

long storage battery shutdown,

or  it  is  operated  when  battery
fluid  level  is  too  low,  or  if  the
battery  is  systematically  under-
charged

Sulfatated plates are corrected by

the charge-discharge cycle with
current not exceeding 1

⁄

20 of bat-

tery capacity, when the initial bat-
tery fluid density is 1.12 g/cm

maximum. Very sulfatated plates
are not repaired

Power Takeoff

Power Takeoff is

not

switching on

Pneumatic

chamber

dia-

phragm of the Power Takeoff is
damaged

Power Takeoof pinion teeth

are worn or damaged

High air leakage due to poor

fastening of the air pipe con-
necting fittings, or their failure

Replace the diaphragm

Disassemble the Power Takeoff,

align gear teeth and replace worn
parts

Detect leakage places by putting

soap  solution  on  the  hose  and  the
plumbing  fittings.  Tighten  the
plumbing  fittings  in  the  leakage
places. Replace defective parts

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 197 / 321

Результаты поиска

Содержание 4320M

Отзывы: