URAL Motorcycles 4320M Скачать руководство пользователя страница 231

Страница: 231 / 321

Scope of work

Technical specifications

Recommended equipment,

devices and tools

Axle configu-

ration

4х4

6х6

Lubricate the interme-

diate bracket shaft of the
clutch linkage and the
brake valve.

Lubricate through oil filet

before the appearance of the
fresh lubricant.

-«-

Unified Maintenance through every 15 000 km of lifetime mileages

(500

hours of engine running)

Engine

Maintain the engine in

accordance  with  the  opera-
tion  manual-1  OM  for  an
engine.

Hereafter

perform

maintenance in accordance
with the operation manual-
2 OM for an engine.

Check and, if neces-

sary, tighten up a fastener
of power unit in all points.

Loosening of the fasteners is

not allowed.

Wrenches 24x27

Check the tightening of

the starting preheater and
the fuel tank.

The same

Wrenches 11х13, 14х17

Check and, if neces-

sary, tighten up the fastener
of all connections of air
injection and exhaust sys-
tems.

-«-

Wrenches 14х17, 17х19

Check the tightening of

the fuel strainer.

-«-

Wrench 14х17

Check the tightening of

the radiator module.

-«-

Wrench 17x19, pliers

Check the tightening of

the air filter.

-«-

Screwdriver,

wrench

10х12

Check and, if neces-

sary,  tighten  up  straps  of
the  cooling  system  and  the
reservoir  pressure  mainte-
nance system.

Coolant leakage is not al-

lowed.

Wrench 7х9, screwdriver

Check and, if neces-

sary, tighten up the fuel
line nut.

Fuel dribbling is not allowed.

Wrench 24х27

Pour residue out of fuel

tank.

Fuel leakage through the

drain plug is not allowed.

Wrench 17x19, сon-

tainer, waste cloth

210

Содержание 4320M


































































































































































































































































































































Результаты поиска

Содержание 4320M

Отзывы:

URAL Motorcycles 4320M, Руководство по эксплуатации, Страница: 231 / 321

Результаты поиска

Содержание 4320M

Отзывы: