manualshive.com logo in svg

Texas Instruments RM48 series, Техническое справочное руководство


Поделиться
Скачать
background image

www.ti.com

HTU Control Registers

1003

SPNU503C – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

High-End Timer Transfer Unit (HTU) Module

21.4.25 Parity Address Register (HTU PAR)

Figure 21-38. Parity Address Register (HTU PAR) [offset = 68h]

31

17

16

Reserved

PEFT

R-0

R/W1CP-0

15

9

8

0

Reserved

PAOFF

R-0

R-X

LEGEND: R/W = Read/Write; R = Read only; W1CP = Write 1 in privilege mode to clear the bit; -

n

= value after reset; X = undefined

Table 21-38. Parity Address Register (HTU PAR) Field Descriptions

Bit

Field

Value

Description

31-10

Reserved

0

Reads return 0. Writes have no effect.

16

PEFT

Parity Error Fault Flag. This bit is set, when the HTU detects a parity error and parity checking is
enabled.

0

No fault is detected.

1

Fault is detected.

Note:

Once PEFT is set, a read access to the lower 16 bits or to the complete 32-bit HTUPAR register

will clear the PEFT flag in non-debug mode. Another possibility to clear PEFT is to write a 1 to the
PEFT bit.

15-9

Reserved

0

Reads return 0. Writes have no effect.

8-0

PAOFF

Parity Error Address Offset. This bit field holds the address of the first parity error, which is detected in
the DCP RAM. PAOFF provides the offset address of the erroneous byte counted from the beginning of
the DCP memory. This error address is frozen from being updated until a read access to the lower 16
bits or to the complete 32-bit HTUPAR register happens. During debug mode, this address is frozen
even when read.

Note:

The Parity Error Address bits will not be reset, neither by PORRST nor by any other reset source.

Содержание RM48 series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM48 series

Eaton A201 Instruction Leaflet preview
A201
Бренд: Eaton Страницы: 6
Federal Signal Corporation UltraVoice Installation, Operation And Service Manual preview
UltraVoice
Бренд: Federal Signal Corporation Страницы: 60
FASTRON. VC-210 Installation And Operating Instructions Manual preview
VC-210
Бренд: FASTRON. Страницы: 16
Galaxy Control Systems 635 Series Worksheet preview
635 Series
Бренд: Galaxy Control Systems Страницы: 5
Gardena EasyPlus Operator'S Manual preview
EasyPlus
Бренд: Gardena Страницы: 14
Gardena 1273 Operating Instructions preview
1273
Бренд: Gardena Страницы: 4
Gantner GAT ACCESS 6100 User Manual preview
GAT ACCESS 6100
Бренд: Gantner Страницы: 4
Viking VC-1000 Technical Practice preview
VC-1000
Бренд: Viking Страницы: 4
Harmonic Drive RSF B mini Series Manual preview
RSF B mini Series
Бренд: Harmonic Drive Страницы: 33
DIG 410BT Series Instruction Manual preview
410BT Series
Бренд: DIG Страницы: 16
Eaton Jockey XTJP O & M Manual preview
Jockey XTJP
Бренд: Eaton Страницы: 12
Altera Stratix III Using Manual preview
Stratix III
Бренд: Altera Страницы: 59
ICP DAS USA CAN-8124 User Manual preview
CAN-8124
Бренд: ICP DAS USA Страницы: 153
aldes 611242-FC Installation Manual preview
611242-FC
Бренд: aldes Страницы: 3
Unika PR-1V Operation Manual preview
PR-1V
Бренд: Unika Страницы: 4
Ubiquiti Raspberry Pi 3B+ UniFi Controller Quick Start Manual preview
Raspberry Pi 3B+ UniFi Controller
Бренд: Ubiquiti Страницы: 4
Naturela NPBC-V3M-1 Manual preview
NPBC-V3M-1
Бренд: Naturela Страницы: 28
Cardin PRG384 Manual preview
PRG384
Бренд: Cardin Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды