manualshive.com logo in svg

Texas Instruments RM48 series, Техническое справочное руководство


Поделиться
Скачать
background image

www.ti.com

Module Operation

1663

SPNU503C – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

Data Modification Module (DMM)

The packet consists only of data bits and no header information. It can be 8-, 16- or 32-bit wide. A variable
packet width is not supported because the DMM module will check the number of incoming bits (DMMCLK
cycles) for error detection. The DMM will write the received data to the destination once the programmed
number of bits has been received.

If the programmed word width does not correspond to the received data, the following actions will be
taken:

•

If the received data is greater than the programmed width, only the configured number of bits are
transferred into the RAM buffer, the additional bits are discarded.

•

If the received number of bits is smaller than the programmed width, no data will be written to the
buffer, because a new DMMSYNC signal has been received before the expected number of bits.

30.2.2 Data Port

The packet will be received in several subpackets, depending on the width of the external data bus
(DMMDATA[y:0]) and the amount of data to be transmitted.

Table 30-4

illustrates the number of clock

cycles required for a complete packet.

Table 30-4. Number of Clock Cycles per Packet

Port Width/ Pins

Write Size in Bits

8

16

32

64

1

32

40

56

88

2

16

20

28

44

4

8

10

14

22

8

4

5

7

11

16

2

3

4

6

The user can program the port width in the DMMPC0 register (

Section 30.3.16

). This feature allows pins

that are not used for DMM functionality to be used as GIO pins. Only the pins shown in

Table 30-5

can be

used for a desired port width.

Table 30-5. Pins Used for Data Communication

Port Width

Pins Used

1

DMMDATA[0]

2

DMMDATA[1:0]

4

DMMDATA[3:0]

8

DMMDATA[7:0]

16

DMMDATA[15:0]

NOTE:

If pins other than the ones specified in

Table 30-5

are programmed as functional pins for a

desired port width, the received data will be corrupted and will not be transferred to the
deserializer.

NOTE:

If DMMCLK or DMMSYNC are programmed as nonfunctional pins, functional operation will

not occur.

Содержание RM48 series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM48 series

ABB LME620-AI Service Instruction preview
LME620-AI
Бренд: ABB Страницы: 30
ABB LME620-AI Instructions Manual preview
LME620-AI
Бренд: ABB Страницы: 15
ABB PST30 Manual preview
PST30
Бренд: ABB Страницы: 10
ABB LME620-AI User Manual preview
LME620-AI
Бренд: ABB Страницы: 44
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Бренд: Danfoss Страницы: 128
Eaton LS Series Instruction Leaflet preview
LS Series
Бренд: Eaton Страницы: 2
Idex Pulsafeeder MPC Vector Installation, Operation & Maintenance Manual preview
Pulsafeeder MPC Vector
Бренд: Idex Страницы: 114
SOMFY Situo 1 RTS Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 4
Reer MOSAIC MA2 Quick Installation Manual preview
MOSAIC MA2
Бренд: Reer Страницы: 2
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Бренд: Acuity Controls Страницы: 5
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Бренд: Bard Страницы: 2
EpiSensor ZDR-10 User Manual preview
ZDR-10
Бренд: EpiSensor Страницы: 37
Burkert 8745 MFC Ethernet Operating Instructions Manual preview
8745 MFC Ethernet
Бренд: Burkert Страницы: 70
HANYOUNG NUX TPR-3SL-EP Instruction Manual preview
TPR-3SL-EP
Бренд: HANYOUNG NUX Страницы: 4
TAC Xenta 102 Handbook preview
Xenta 102
Бренд: TAC Страницы: 76
Patton SmartNode 5501 User Manual preview
SmartNode 5501
Бренд: Patton Страницы: 56
Abov A96G140 User Manual preview
A96G140
Бренд: Abov Страницы: 278
Zennio MAXinBOX66 Technical Documentation preview
MAXinBOX66
Бренд: Zennio Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды