manualshive.com logo in svg

Texas Instruments RM48 series, Техническое справочное руководство


Поделиться
Скачать
background image

Module Configuration

www.ti.com

1146

SPNU503C – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

Multi-Buffered Serial Peripheral Interface Module (MibSPI) with Parallel Pin
Option (MibSPIP)

24.8 Module Configuration

MibSPI/MibSPIP can be configured to function as Normal SPI and Multi-buffered SPI. Upon power-up or a
system-level reset, each bit in the module registers is set to a default state. The registers are writable only
after the RESET bit is set to 1.

24.8.1 Compatibility (SPI) Mode Configuration

The following list details the configuration steps that software should perform prior to the transmission or
reception of data. As long as the SPIEN bit in the Global Control Register 1 (SPIGCR1) is cleared to 0 the
entire time that the SPI is being configured, the order in which the registers are programmed is not
important.

•

Enable SPI by setting RESET bit.

•

Configure the SIMO, SOMI, SPICLK, and optional SPICS and SPIENA pins for SPI functionality by
setting the corresponding bit in SPIPC0 register.

•

Configure the module to function as Master or Slave using CLKMOD and MASTER bits.

•

Configure the required SPI data format using SPIFMTx register.

•

If the module is selected to function as Master, the delay parameters can be configured using
SPIDELAY register.

•

Enable the Interrupts using SPIINT0 register if required.

•

Select the chip select to be used by setting CSNR bits in SPIDAT1 register.

•

Configure CSHOLD and WDEL bits in SPIDAT1 register if required.

•

Select the Data word format by setting DFSEL bits. Select the Number of the configured SPIFMTx
register (0 to 3) to used for the communication.

•

Set LOOPBACK bit to connect the transmitter to the receiver internally. (This feature is used to perform
a self-test. Do not configure for normal communication to external devices).

•

Set SPIEN bit to 1 after the SPI is configured.

•

Perform Transmit and receive data, using SPIDAT1 and SPIBUF register.

•

You must wait for TXFULL to reset or TXINT before writing next data to SPIDAT1 register.

•

You must wait for RXEMPTY to reset or RXINT before reading the data from SPIBUF register.

Содержание RM48 series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RM48 series

C Prox Ltd FP1 User Manual preview
FP1
Бренд: C Prox Ltd Страницы: 5
Technische Alternative UVR 63H Operation And Installation Manual preview
UVR 63H
Бренд: Technische Alternative Страницы: 68
Industrial Controls MC-2120 Operating And Maintenance Manual preview
MC-2120
Бренд: Industrial Controls Страницы: 17
2N 9160341 Installation Manual preview
9160341
Бренд: 2N Страницы: 107
Allen-Bradley Micro850 series Installation Instructions Manual preview
Micro850 series
Бренд: Allen-Bradley Страницы: 24
Rabbit microBLUE Instruction Manual preview
microBLUE
Бренд: Rabbit Страницы: 12
TAC Xenta 102 Handbook preview
Xenta 102
Бренд: TAC Страницы: 76
G-Tech FIELD MATE User Manual And Installation Manual preview
FIELD MATE
Бренд: G-Tech Страницы: 26
Guangdong Schen Investment RC-M2 User Manual preview
RC-M2
Бренд: Guangdong Schen Investment Страницы: 15
Aerotech ABL9000 Series User Manual preview
ABL9000 Series
Бренд: Aerotech Страницы: 36
Jetter JCM-521 Installation Manual preview
JCM-521
Бренд: Jetter Страницы: 30
ZPA Pecky, a.s. MODACT MTNED 15 Mounting Instructions preview
MODACT MTNED 15
Бренд: ZPA Pecky, a.s. Страницы: 48
OK-I PTZ-KB050 Operational Manual preview
PTZ-KB050
Бренд: OK-I Страницы: 10
Danfoss VLT LCP 601 Installation Manual preview
VLT LCP 601
Бренд: Danfoss Страницы: 8
Autoscript WB-IP User Manual preview
WB-IP
Бренд: Autoscript Страницы: 22
Hall Research Technologies CNT-IP-264 User Manual preview
CNT-IP-264
Бренд: Hall Research Technologies Страницы: 16
YASKAWA MotionWorks IEC Example Code Manual preview
MotionWorks IEC
Бренд: YASKAWA Страницы: 21
YOKOGAWA STARDOM FCN-500 Engineering Manual preview
STARDOM FCN-500
Бренд: YOKOGAWA Страницы: 226

Бренды по названию

Популярные бренды

Загрузить еще бренды