Keysight N9923A Скачать руководство пользователя страница 89

Страница: 89 / 276

Keysight N9923A Handheld Analyzer
User’s Guide

DTF (Distance to Fault) Measurements

CAT Mode

Distance to Fault

(DTF) measurements are generally used to locate

problems, or faults, in a length of cable or transmission line. In this chapter, the

cable to be tested is referred to as the DUT (Device Under Test).

Settings that are NOT unique to DTF measurements are documented in

Chapter 5,

“CAT (Cable and Antenna Test) Mode”, on page 75

In this Chapter

Optional settings

“How to make DTF Measurements” on page 90

“DTF Settings Table” on page 91

“DTF Measurement (Format)” on page 91

“DTF Start and Stop Distance” on page 92

“Frequency Mode” on page 92

“Coupled Frequency” on page 93

“Cable (Correction) Specifications” on page 94

“Window Settings” on page 97

“DTF Units” on page 98

“Calculated DTF values” on page 98

“About Alias Faults” on page 98

“All about Markers” on page 174

“All about Limit Lines” on page 185

“Saving and Recalling Files” on page 192

Trace Math is NOT available in DTF Measurements.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 89 / 276

Результаты поиска

Содержание N9923A

Отзывы: