Keysight N9923A Скачать руководство пользователя страница 116

Страница: 116 / 276

116 Keysight N9923-90001 User’s Guide

Calibration for NA, CAT, and VVM Modes

Sweeps in BOTH directions.

FULL 2-Port (QSOLT) – Mechanical Cal ONLY (Requires Option)

Quicker to perform QSOLT than Full 2-port. Corrects all S-parameters.

DUT: Insertable only

Standards: OPEN, SHORT, LOAD on port 1. Flush THRU between ports.

Recommended cal type for Insertable DUTs. A Cal Kit is NOT required for
port 2.

Sweeps in BOTH directions.

Enhanced Response Cal - Forward OR Reverse (May require an option)

Faster measurements than Full 2-Port.

DUT: Non-Insertable or Insertable. S-parameters PARTIALLY Corrected:
S21 and S11 (Forward)

S12 and S22 (Reverse)

Standards: OPEN, SHORT, LOAD on

ONE

port. Defined THRU between

ports.

Sweeps in ONE direction.

TRL – Mechanical Cal ONLY

A complete 2-Port calibration with potentially better accuracy than Full
2-port. Corrects all S-parameters.

DUT: Non-Insertable or Insertable

Standards: Thru, Reflect, Line or variations of these. A TRL Cal Kit MUST be
selected to see this Cal Type

Sweeps in BOTH directions.

Learn more about TRL Calibration in the

Supplemental Online Help

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

1-port Response Cals (Open or Short)

Calibrate the magnitude and phase of a measurement using ‘modeled’
mechanical standards. Measurement accuracy is better than Simple

Response Cals (available on the main Cal page - see

“Calibration Type” on

page 114

) but NOT as good as full 1-port cal. Corrects either S11 or S22.

Can be used with Isolation (see following section). Learn more in

“Simple

Response Cals ” on page 112

DUT: Non-Insertable or Insertable

S-parameters Corrected: S11 or S22

Also select an Enhanced Response Optimization. Learn more in

“Enhanced

Response Optimization” on page 119

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 116 / 276

Результаты поиска

Содержание N9923A

Отзывы: