Keysight N9923A Скачать руководство пользователя страница 197

Страница: 197 / 276

Keysight N9923-90001 User’s Guide

197

File Management
Saving and Recalling Files

—

USB

Saves/Recalls/Moves (Copies) files to or from a USB Flash drive

(not included) that is inserted in one of the USB connectors. Only the

root folder is available.

How to set File Type

— Press

Save/Recall 9

— Then

File Type

. Choose one of the following:

—

State

Saves ALL FieldFox instrument settings for ALL Modes to a *.sta

file. If a calibration is ON in CAT or NA Mode, calibration data is also
saved. This file can be opened ONLY by a FieldFox. State files can be

saved between compatible FieldFox models. See note in.

“Saving and

Recalling Files” on page 192

—

Trace+State

Saves the current trace and instrument settings to a *.sta

file. In SA Mode, all traces are saved. This file can be opened ONLY by
a FieldFox. When recalled, the FieldFox sweep is set to Hold.

—

Picture

Saves a 640 x 453 pixel image of the FieldFox screen to a *.png

file. The picture does NOT include the softkeys.

—

Data (csv)

Saves trace data from the current Mode to a *.csv file. This

format can be imported into spreadsheet software such as Microsoft

Excel. Column A is always the frequency at which the data is
measured.

——In

CAT

and

Modes, only the data trace is saved – not the

memory trace.

——In

Power Meter

and

VVM

Mode, NO data is saved.

—

Data (S1P) / (S2P)

Saves

CAT

and

Mode trace data to an *.S1P or

*.S2P file, depending on the active measurement. This file format is

used by CAE programs such as Keysight's Microwave Design System
(MDS) and Advanced Design System (ADS). It can also be imported
into spreadsheet software such as Microsoft Excel.

About SNP Files

The SNP file includes header information, and the following data:

— S1P - saves 1-port (receiver) data for the active data trace. *.s1p Files

contain 1 stimulus value and 1 S-parameter (total of 3 scalar values)

Stim

Real(Sxx) Imag(Sxx)

— S2P (NA Mode ONLY) - saves 2-port data for the active trace. *.s2p

Files

contain 1 stimulus value and 4 S-parameters (total of 9 scalar values)

Stim

Real(S11) Imag(S11) Real(S21) Imag(S21) Real(S12) Imag(S12)

Real(S22) Imag(S22)

Insert only ONE USB Flash Drive in the FieldFox when saving or copying

files.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 197 / 276

Результаты поиска

Содержание N9923A

Отзывы: