Keysight N9923A Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 276

Keysight N9923A Скачать руководство пользователя страница 22

22 Keysight N9923-90001 User’s Guide

Preparing for Initial Use of Your New FieldFox
Install the Lithium-Ion Battery

Install the Lithium-Ion Battery

Battery Usage

When you receive your FieldFox, the lithium-ion battery is not installed, and it
is partially charged to approximately 40% to preserve battery life. A lithium-ion

battery has no memory effect, so it can be used partially charged, as shipped.

A fully charged battery will power your FieldFox for about four hours, so if you

plan to use it for this long, you should fully charge the battery.

Learn more about the lithium-ion battery in

Chapter 16, “Working with the

Lithium-Ion Battery”, on page 239

Battery charge status is viewable:

—

In the upper-right corner of the screen.

— On the Battery screen. To access the screen, select

System

,

Service

Diagnostics

, and

Battery.

Step

Notes

1. Open the battery door

Push the button on the battery compartment door while sliding the

door outward.

2. Insert the battery.

The terminals end of the battery is inserted into the compartment.

3. Close the battery door.

Slide the battery compartment door upwards until it latches.

The FieldFox will shut down to prevent the battery from discharging to a

level that is damaging. If this occurs, charge the battery either internally or

externally.

«
...
20
21
22
23
24
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов