Keysight N9923A Скачать руководство пользователя страница 213

Страница: 213 / 276

Keysight N9923-90001 User’s Guide

213

System Settings
Preferences

— Then

Title ON OFF

to make the title appear and disappear from the screen.

Edit Keywords

During a file save operation, keywords can be quickly appended to other text to

create unique filenames. The Edit Keywords feature allows you to create
custom keywords. Learn all about Edit Keywords in

“Edit Keywords” on

page 201

Full Screen Mode

Full Screen Mode maximizes the display of trace. The screen annotations and
the soft keys are removed.

— Press

System 7

— Then

Full Screen

Exit

full screen Mode, press any key.

Preferences

FieldFox preferences are settings that survive a shut down. When your FieldFox

is turned OFF, then back ON, these settings remain. All preference settings can
be restored to their factory defaults. Learn how in

“Save and Reset

Preferences” on page 214

There are two ways to make FieldFox preference settings:

— From softkey selections throughout the FieldFox menu structure. Do this to

temporarily try a setting, then press

Save Current Preferences

. Learn how

in the next section.

— From the Quick Settings table.

Quick Settings Table

All preferences can be set from the Quick Settings table. They are immediately
saved as Preferences when

Done

is pressed.

How to view and change Preference Quick Settings

— Press

System 7

— Then

Preferences

— Then

Preferences

— Press

Next Page

and

Previous Page

to view all settings.

— To change a setting:

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 213 / 276

Результаты поиска

Содержание N9923A

Отзывы: