Keysight N9923A Скачать руководство пользователя страница 220

Страница: 220 / 276

220 Keysight N9923-90001 User’s Guide

System Settings
Preferences

——dddº mm’ ss.sss”

——ddd.dddddddº

——dddº mm.mmmmm’

—Then Done Edit (for each change in setting)

File folders

When enabled, FieldFox uses the last selected Device and Folder location as the
default device location after instrument power cycle.

How to set File Folders

— Press

System 7

— Then

Preferences

— Then

Preferences

— Then scroll to

User Folder Persist:

—

User Folder Persist (On/Off)

– Defaults to the current Device and

folder location at power up. Toggle User Folder Persist On/Off when a
new Device location is selected location.

—

User Folder

– displays the default folder location.

—

User Device

– displays the default device location.

Alpha Numeric Editing

—

Keyboard Style

– Toggles through Qwerty/ABC style keyboards that the

Labeler displays. Refer to

“How to use the FieldFox labeler ” on page 193

File Saving Naming Options

—

Prefix

– Displays the current choice for Prefix. Choices are User, Last File

(default), or Off. Refer to

“Prefixes and Suffixes for Filenames” on page 202

—

Auto Append

– Displays the current choice for Auto Append to a filename

(Suffix). Choices are Off (default), Number, Date. Refer to

“Prefixes and

Suffixes for Filenames” on page 202

CAT (Distance Units)

Choose the CAT distance units (i.e., Meters (default), Feet, Inches). See

“DTF

Units” on page 98

How to select CAT distance units:

Before setting the preferences for the File Folders, you must select

the

Device and Folder locations. Refer to

Chapter 13, “File Management”, on

page 191

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 220 / 276

Результаты поиска

Содержание N9923A

Отзывы: