Keysight N9923A Скачать руководство пользователя страница 98

Страница: 98 / 276

98 Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

DTF Units

The DTF Units setting is available ONLY on the DTF Settings table.

By default, X-axis units for DTF measurement settings are displayed in Meters.

How to change DTF units

— With a DTF measurement present, press

Freq/Dist

— Then

More

then

Distance Unit m feet

— The current selection is underlined

m (meters) Feet

Calculated DTF values

Press

Next Page

on the DTF Settings Table to view the following

calculated

Value

s noted on the FieldFox screen with c - <setting>

Start Frequency

– Start frequency that is used to calculate DTF.

Stop Frequency

– Stop frequency that is used to calculate DTF.

Range Resolution

. Indicates the accuracy of the distance to fault

measurement. For example, with range resolution of 500 mm, if the distance to
fault is 10 meters, this value could be inaccurate by +/- 500 mm or between

9.5 to 10.5 meters. This value is calculated from frequency span / resolution
(points).

Response Resolution, not displayed, indicates the distance that could be
between two faults and still show as separate faults. Learn more in

“Window

Settings” on page 97

Maximum Distance

. The distance that could be viewed with the current

settings. Defined by: Vf*c*Points/(2*Bandwidth) where:

— Vf = velocity factor

— c = speed of light

— Points = resolution

— Bandwidth = frequency range
Alias-free Range (On/Off)

— On = No Alias images

— Off = Alias images may appear in the response.

About Alias Faults

An alias fault is not a true device response. An alias fault appears because of
the method used to convert frequency to time.

On the DTF Settings page (above) the c - Alias-free Range = Off setting
indicates alias images MAY appear on the screen.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 98 / 276

Результаты поиска

Содержание N9923A

Отзывы: