Keysight N9923A Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 276

Keysight N9923A Скачать руководство пользователя страница 108

108 Keysight N9923-90001 User’s Guide

Calibration for NA, CAT, and VVM Modes

—When your DUT has high return loss such as the reject band of a filter.

Then measuring the load improves accuracy. Even with the optional

Load, phase accuracy begins to degrade when the return loss is
greater than about 20dB.

— Press

Skip Step

in all other cases and when making DTF measurements.

Measuring a load would do little to improve accuracy.

Connect THRU (Not used for 1-port cals)

— Connect port 1 to port 2, either by mating the connectors that attach to the

DUT (Flush THRU), or by using a short jumper cable. Learn more about

Flush THRU in

“Calibration Type” on page 114

. Then press

Measure

.

— Press

Finish

.

CAL ON Q

is shown on the screen for all displayed measurements that are

corrected with QuickCal.

Using QuickCal with a Long Jumper Cable

QuickCal requires a sufficient frequency span to adequately characterize the
jumper cable (the cable between the instrument port and the DUT). If a ‘Cal

Failed’ error appears and you connected the optional Load standard, then
increase the frequency span of the measurement until the error no longer
appears. After the calibration, you can then decrease the frequency span as

needed and rely on interpolation. Learn more about Interpolation in

“Interpolation *” on page 119

QuickCal is also limited in how much jumper cable loss it can tolerate. If
QuickCal without the Load is failing, then measure the Load during the
QuickCal to see if that resolves the issue.

Mechanical Cal

Mechanical Calibration is performed using discrete standards from a Cal Kit.
Several Cal Kit definitions are built into the FieldFox. To learn about Cal Kit
definitions, refer to the Application Note, “Specifying Calibration Standards

and Kits for Keysight Vector Network Analyzers,” available online at

http://literature.cdn.keysight.com/litweb/pdf/5989-4840EN.pdf

Mechanical Cals are extremely accurate when performed using the correct Cal

Kits with standards that are clean and in good repair, and when using correct
connection procedures.

How to perform a Mechanical Cal

— Disconnect the DUT from the FieldFox.

Visit

www.keysight.com/find/fieldfoxsupport

to see a complete list of

supported Cal Kits. Also at this website, download Data-Link software that

allows you to edit Cal Kit definitions or add a new Cal Kit.

«
...
106
107
108
109
110
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов