Keysight N9923A Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 276

Keysight N9923A Скачать руководство пользователя страница 65

Keysight N9923-90001 User’s Guide

65

Time Domain – Option 010
Time Domain (Transform) Settings

Stimulus (Mode)

— There are three variations on how the Time Domain transform algorithm is

applied to the frequency domain measurement. Each method has a unique
application.

—

Lowpass Impulse

- Highest resolution. Most useful for seeing small

responses in devices that pass low frequencies, such as cables.

—

Lowpass Step

- Easiest to identify inductive and capacitive discontinuities

in devices that pass low frequencies such as cables.

In both Lowpass modes, frequencies down to DC and negative frequencies are

extrapolated. Therefore, when either Lowpass mode is selected,

Set Freq.Low

Pass

is automatically applied to adjust the start frequency. Learn more about

Set Frequency Lowpass below.

When the Start Frequency or resolution is changed AFTER selecting a Lowpass
mode, then Stimulus mode is set to Band Pass and Transform is disabled.

—

Band pass

- Easiest method - can be used with any frequency sweep. Most

useful for measuring band limited devices such as filters and DC blocked

cables. This mode does NOT show capacitive and inductive reactance. For
the same frequency span and number of points, band pass mode has twice
the impulse width, which hides closely spaced responses degrading the

response resolution.

Set Frequency Lowpass

USE ONLY IN LOW PASS MODES. The Low Pass Start frequency is adjusted so
that the Low Pass Stop frequency is at harmonics of the Low Pass Start

frequency. Start frequency is computed by the following formula:

Low Pass

Start Frequency = Stop Frequency / Number of points

.

Start/Stop Time

The following settings adjust the

display resolution

, allowing you to zoom IN

or OUT on a response. When the start or stop time is updated, they may be
automatically adjusted to limit the display to one alias-free response on either
side of zero time.

How to set Start and Stop time

— Press

Measure Setup 4

— Then

Transform

— Then

Transform Start Stop

This setting is made automatically when either Lowpass mode is selected.

«
...
63
64
65
66
67
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов