Keysight N9923A Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 276

Keysight N9923A Скачать руководство пользователя страница 171

Keysight N9923-90001 User’s Guide 171

VVM (Vector Voltmeter) Mode - Option 308
2-Port Transmission Measurements

2-Port Transmission Measurements

A 2-Port Transmission measurement is used for measuring electrical length,

insertion loss, gain, or isolation of a DUT at a single CW frequency. The
FieldFox signal source is transmitted out the port 1 connector, through the
DUT, and into the port 2 connector. In the following image, the gain of an

amplifier is being measured.

Figure 11-3

2-Port Transmission measurement of an amplifier

How to make a 2-Port Transmission Measurement

1.

Press

Mode

then

VVM

then

2-Port Transmission

.

2.

Press

Freq/Dist

and enter the measurement frequency.

3.

Press

Meas Setup 4

then

More

then

Output Power

. Select

High

for passive

devices. Select Low for amplifiers.

4.

Calibrate the FieldFox using one of the methods described in

Calibration” on page 167

. Before performing a QuickCal or Mechanical

Cal, press

Meas Setup 4

then

Zero OFF

.

5.

Connect the DUT.

Notes:

— The magnitude value is the gain (positive value) or the loss (negative value)

of the DUT.

— The phase value is the difference in phase (in degrees) between the DUT

input and output.

— To measure isolation of the amplifier, reverse the connection to the amplifier

(

PORT 1

to the amplifier output).

«
...
169
170
171
172
173
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов