Keysight N9923A Скачать руководство пользователя страница 153

Страница: 153 / 276

Keysight N9923-90001 User’s Guide 153

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

— Then

Trig Type

— Then choose from the following:

—

Freerun

The USB Power Sensor acquires data without waiting for a

trigger. This mode is NOT supported for Trace Graph measurements.

—

Internal

The USB Power Sensor acquires data when a valid pulse

signal is detected at the RF input. The following Trigger settings
determine the validity of the trigger signal.

—

External

The USB Power Sensor acquires data when a valid TTL

signal is detected at the USB Power Sensor external trigger input.

Trigger Edge

This setting determines which edge of a trigger signal initiates data

acquisition.

— Press

Sweep 3

— Then

Trigger

— Then

Trig Edge

— Then choose from the following:

—

Pos

Acquisition is triggered by the rising (positive) edge of a valid

signal.

—

Neg

Acquisition is triggered by the falling (negative) edge of a valid

signal.

Trigger Delay

After a valid trigger signal is received at the USB Power Sensor, data
acquisition begins after the specified Trigger Delay time PLUS the specified
Start time. See the Pulse Timing diagram in

“Trigger Settings Annotation” on

page 154

for more information.

— Press

Sweep 3

— Then

Trigger

— Then

Trig Delay

— Then enter a value using the numeric keypad, the

arrows, or the rotary

knob.

Auto Trigger

Used ONLY when Trigger Type = Internal, this setting determines whether the

trigger level is set manually or is set to the default level in the USB Power
Sensor firmware.

— Press

Sweep 3

— Then

Trigger

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 153 / 276

Результаты поиска

Содержание N9923A

Отзывы: