Keysight N9923A Скачать руководство пользователя страница 130

Страница: 130 / 276

130 Keysight N9923-90001 User’s Guide

Power Meter (USB) Mode
USB Power Meter Settings

— Then

Advanced

— Then

Source Enable

—

Turn ON the internal source

—

OFF

Turn OFF the internal source

Optionally set the power level.

— Press

Src Nom Power

(-15 dBm default setting) Set output power to an

arbitrary value at the displayed CW frequency.

— Then enter a value using the numeric keypad, the

arrows, or the rotary

knob.

— Press

Enter

Scale

The scale of the Power Meter display can be set manually or automatically. The
major and minor ticks are set automatically and can NOT be changed.

Although the scale settings are limited, you can view measurements beyond
these settings by performing Autoscale.

How to Scale the Power Meter Display

Manually:

— Press

Scale / Amptd

— Then choose from the following:

—

Scale Min

Sets the low power level of the power meter display. Type

a number and select the units or press Enter. This value is limited to
–100 dBm.

—

Scale Max

Sets the high power level of the power meter display.

Type a number and select the units or press Enter. This value is

limited to 100 dBm.

Autoscale:

Using Autoscale, the current reading is used for the center of the scale, and
Min and Max values are set accordingly.

When Option 208 (FOPS) is enabled, to access Source Control, press

Sweep 3

then

Power Setup

Learn more about FOPS beginning on page

Chapter 9, “Frequency Offset Using Power Sensor (FOPS) – Option 208”,

on page 135

Amplitude accuracy may be compromised when the Source is ON, Battery Saver is ON,

and the Preamp is ON. For highest amplitude accuracy under these conditions, turn

Battery Saver OFF. Learn how in.

“Maximizing Battery Life” on page 244

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 130 / 276

Результаты поиска

Содержание N9923A

Отзывы: